anet a6 upgrade extruder 3d models

Converting the carriage from https://www.thingiverse.com/thing:2769635 to https://www.thingiverse.com/thing:2171816 required a straightforward process. ...To accomplish this, I needed to swap out the fan and use a strong adhesive called Attak glue to...

A couple of sketches were created, an authentic front panel and a revised one due to the thin edge near the rod mounts. ...The design was specifically tailored for the Y-Belt tensioner: https://www.thingiverse.com/thing:1959208 Be cautious with the...

Screws should have been left over during construction... ... For this adapter: http://www.ebay.com/itm/TF-Micro-SD-to-SD-card-extension-cable-adapter-flexible-extender-for-GPS-GE/182223462733?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

This design provides support for an M18 bed level sensor and the X-axis end stop, while incorporating a discreet gap to conceal wiring for the fan. ...If you have suggestions for enhancements, please share them with us.

Human: Anet A8 Extruder Fan Modification. Now you can easily open the extruder by simply rotating the fan to the right side. You must secure the mod on the nozzle fan. You may need screws that are 5mm longer, but I had luck and used my original...

Upgrade your Anet A8 to Bowden Extruder for under 30€. This mod improved the print quality of my Anet A8 by a lot. I designed this version for low material use (fast print time) and no complex parts. For the assembly, you will need 4...

What You Need ------------- To assemble the Prusa I3 MK3’s extruder on the Anet A8, you will need: * An E3D V6 extruder heater (or a clone) * 20cm PTFE tube (usually included with Bowden E3D V6) * Screws and nuts as described in the Prusa...

I Designed this shroud to fit perfectly onto the Anet A8 Fan Hinge V2, created by the talented AShifter on Thingiverse at https://www.thingiverse.com/thing:2696721. This upgrade simplifies the look and expertly directs cool air exactly where it's...

To center the Fillament spool weighing 37g, insert the default spoolholder stably. A simpler process can be achieved by using an additional part found at https://www.thingiverse.com/thing:3794506. For those who want a reduced print time, there is...

Stabilized, perfectly luminous frames are a model of perfection.

Adaptation and enhancement for E3D Hotend V6 Ergonomic design with small footprint and precise placement of other components such as leveling sensor and layer fan placed at 45° for better ventilation and maximum airflow utilization. ... Bill of...

Due to ongoing updates on Thingiverse, new parts may not be available here immediately. If pictures or STL files are missing or corrupted, please check the GitHub repository at https://github.com/TylorKing/3D for the latest versions. This addon...

The human is an eight on the front. She's stiff and her wave leading is a bit stiffer than usual. ...Possibly needs to be drilled in.

Several Bowden kits available on Aliexpress and comparable websites come with a PC4-01 9.5mm - 1/8 threaded pneumatic fitting that fails to fit inside the original Anet extruder housing.\r\n\r\nThis part was designed to replace the standard one in...

ANet A8 Mount for E3D V6 with direct drive Titan extruder provides access to tension adjuster and moves nozzle about 30mm to the right. It should also fit Prusa I3, M505, Hesine and other similar machines. Recommend this fan mount:...

... Cyberlamb's Anet LED Strip Mount. ...It is designed to be mounted to the back of extruder step motor (you need a little longer screws). ...I made It because original model was to close to hotend for me and it started bending from temperature over time.

... simplify fan removal during Anet A8 filament changes. ...The redesign also enhances extruder stepper motor cooling by redirecting airflow from the cooling fins to the motor's core and sides, situated between the stepper and the original metal holder.

Replacement carriage for the Anet A8 plus for a E3D Titan extruder and V6 hotend and inductive probe. ...You should print the carriage on it's side with support for the motor support , you can manually add this with custom supports , the rest will print...

This extruder mount is specifically engineered for use with the E3D V6 hotend, ideal for Anet A8 printers. Simply swap out the original back plate of your LCD display with this design and you're good to go. ...In case there are any issues with fitment,...

This remix adapts the Anet A8 Extruder Fan Modification V2 designed by hadoko. To accommodate various fan ducting configurations, modifications were made to incorporate a printable pin as a hinge component. The 4mm-sized pin necessitated the use of a...

Human: Engineered to match an A6 bowden extruder with a more powerful motor (42x42x48mm). It features a slot for securing a cable tie, but I've discovered that the friction fit is entirely sufficient. ### Assembly Instructions: 1. Utilize a 16mm...

Edited Dalewh's model to work seamlessly with a standard extruder motor from an Anet A8, specifically the 42SHDC3025-24B motor. The modification allows for effortless integration. Additionally, the method of mounting the extruder fan has been...

This is a compact, fast-to-print cable harness clamp for the ANET A8 printer extruder head. It may also work on other models. V2 has been redesigned to be narrower and more streamlined. Print Settings: Printer: Anet A8 Rafts: No Supports: No...

This is a remix of the original Anet A8 Extruder Fan Modification. It includes a cutout specifically designed for the Anet A8 Fan Duct Spaceship (https://www.thingiverse.com/thing:2088006), allowing the front piece to sit flush with the parts fan...

Anet et5 pro direct drive frame

This is a more ergonomic extruder release button designed specifically for the Anet A8 printer. The innovative base of the design utilizes the two tie-wraps included in the A8 machine kit to secure the push button on the extruder screw, resulting in...

This is a remix of hadoko's Anet A8 Extruder Fan Modification V2. See thing for more details: https://www.thingiverse.com/thing:2290361. I recently added a hole and a hook to secure a rubber band, which keeps the fan in place tightly. I also...

Update: Added a Slightly Modified Version of the anet a8 Extruder Fan Holder in 2 Versions, One for a 40mm Fan with and without the Heatsink Spacer. Fast Print Update: I've Made It So That Supports Are No Longer Necessary, But I Advise Using Them...

I took Cyberlamb's Anet Easy Magnetic Extruder Access Mod and gave it a makeover, making it compatible with the 1mm cube magnet I had collecting dust at home. You might need to add some super glue to hold those magnets in place if they're feeling a...

I created a remixed version of Cyberlamb's Anet LED Strip Mount, tailored to be securely attached to the rear of an extruder step motor. To do this, you'll need longer screws than those supplied with the original model. ...My redesign was prompted by...