anet a6 upgrade extruder 3d models

This is a dual z-endstop mount, perfect for adding two endstops at the same height with just two prints. I'm using this mount on my Marlin/Ramps conversion, which has proven to be a solid setup.\r\n\r\nUPDATE:\r\nI also created a version of this...

My primary objective was to position the pulley in alignment with the stepper motor and ensure the tension screws are in a straight line with the pulley. The pulley's center-to-center measurement on my printer is exactly 36 millimeters above the...

The ultimate Y-belt holder boasts a height of 16 mm above the mounting plane, a full 3 mm taller than its original counterpart. This design is specifically engineered to work seamlessly with reinforced hotbed ground plates, heightened SC8UU...

After swapping out the z-carriages for a design inspired by runtimeterror (2831084), the original z-endstop proved to be a major headache due to its non-adjustable nature. ...Since the adjustable holder suggested by qrisonline wouldn't mesh with the new...

After printing and installing thing 2106854 from https://www.thingiverse.com/, my printer's z stop switch stopped getting triggered. To fix this problem, I designed a new bracket that lowers and moves the switch into position where it will be hit by...

I didn't require two slots for the MOSFETs because I'm only using one for the heating bed. Additionally, I opted against a rectangular design; it just wasn't what I wanted. Anyway, here's my revised version of the remix. ...It fits well and I'm...

I'm the sole enthusiast who drove me to create this, a custom-built fan that measures an impressive 140 millimeters in diameter. ...Crafted primarily to safeguard those pesky wires from getting tangled with the fan itself, it serves as a reliable...

Hello, I'm glad you asked about this spacer design. As for the z-achsis threaded rod, I intentionally created it to minimize its wobble. By clipping it tightly into place, the rod is now stabilized and has very little room for movement. I'd love to...

Print Settings Rafts: Disabled Supports: Not Required Resolution: Set to 0.4mm Infill: 100% Density Notes: Optional supports can be used for the mount plate, if needed.

Mount the sensor autocalibration table "3D touch" and attach the spacer between the fan and the radiator. The sensor is not yet connected, requiring a printer reflashing. ... -------------------------------------------------------- All my designs can...

Valid Support for 80x80x25 Fan A reliable fan requires six neodymium magnets, each with a diameter of 5 millimeters and a length of 4 millimeters. ...These magnets can be purchased from Amazon or AliExpress.

I managed to strip the screws within the endstops as I tightened the switch. ...They're identical to the original endstops that came with the printer.

Bed Leveling Measure Gauge Holder Need Some M3 Screws Gauge: ...

You can prevent from X tension to bend the piece where the motor is attached

Made a long time ago for future reference by someone who needed it. This is an addition to https://www.thingiverse.com/thing:2820833. I conducted numerous test prints to ensure the cable chain was centered perfectly. To fit my enclosure snugly, I...

Humans operate at a microscopic scale of 0.2 millimeters as they carefully fill the gaps, achieving an impressive 40% capacity with precision and control. ...Their speed is remarkable, moving at a rate of 60 millimeters per second with ease and...

Typically, my printer is situated on the left side of me, and I've always found myself constantly searching for the SD cards. This is precisely why I created a designated space to store them conveniently close by and easily accessible. ... This...

This LED mount is an absolute blast to print! I've uploaded my printed version for you to see how I managed it. I used a 0.2mm layer height and slowed down the speed. But once you've printed it, the real magic happens! Mount two white 5mm LEDs,...

I'm hopeful that it will function properly.

To use the ToolBox with LCD Cover mounted, follow these steps. This thing was created using Tinkercad. You can edit it online at https://www.tinkercad.com/things/1ALissSN39n. LCD Cover: Visit https://www.thingiverse.com/thing:2170152 for more...

Cable Management System: Main Cable Route runs parallel to the back edge of the display, perfectly centered for maximum efficiency.

This versatile clip keeps your USB to SD card adapter neatly organized, attaching easily to the side of your printer for an instant storage solution. ...It even doubles as a convenient holder for a thin paper scraper, perfect for any unexpected cleaning...

This section must be followed whenever you need to tighten a Y-belt due to inward curvature of the back frame during tightening.

I had to create an endstop plate for my Tatara frame because it wasn't included when I received it. To do this, I took the yes.dwg file from Tatara's website and converted it into a dxf file using an online tool. After that, I imported the new file...

Easy-to-assemble wing nut replacement for hot bed. This design requires embedding a 3mm threaded nut, utilizing a wooden piece and a hammer to secure it in place. You can tighten the bolts and springs by screwing the device using your fingers or with...

Woodworkers swiftly rectify the wobbly issue on wooden panels by securely fastening the corner of the z-axis.

Another filament guide, still discovering the ropes.

If you appreciated this project and want to express your gratitude, please consider showing your appreciation by sending a tip on Thingiverse or supporting me through my PayPal account <a href="https://paypal.me/ArturPetrzak">here</a>. This part...

The basic design of a standard 40mm fan duct revolves around a simple, straightforward configuration that allows for effective airflow management.