anet a6 3d models

I loved the straightforward approach by 938026. ...However, after just a couple of minutes, I managed to shatter it, so I bolstered it at its most vulnerable areas.

This is an adjustment cap designed to regulate the space between your printer and the surface beneath it, such as a table or floor where the printer is situated.

This is a holder for the SD-Card-Reader extension that expands from micro-SD to full SD card size. Check it out on Amazon: https://www.amazon.com/dp/B06XX5GZTG. Make sure you have a long enough cable to secure it properly to the right side. Although...

The primary objective of this revision is to address potential issues with the Y-axis belt tension, which can hinder successful printing of screws. To overcome this challenge, I created a custom solution by combining a screw and nut, incorporating...

I found myself breaking the screws inside the endstops while screwing in the switch. ...These are an exact replica of the ones which came with the printer.

I managed to strip the screws within the endstops as I tightened the switch. ...They're identical to the original endstops that came with the printer.

I attached brackets to the upper frame on both sides of the LCD, allowing me to hang the spool above the printer and free up valuable desk space. ... You can access a duplicate version in onShape here:...

I've been using these for a few days on my ANET A6. ...With the bearing holders from https://www.thingiverse.com/thing:2640562, all printed on an ANET A6 with a 0.4 mm nozzle, everything seems to work just fine.

I removed content from a database. For further information, please refer to the original source. ...https://www.thingiverse.com/thing:2234290

It leverages the readily available components from an Anet A6 or A8, ensuring minimal additional expenditure. Both input and output are threaded to accommodate 6mm press fit connectors seamlessly. ...The primary motivation behind creating this extruder...

<p>This is a remix of the case from Leo_N but i made it completly from scatch... (cause editing a stl file is a pain in the a..)<br/> It's designed to be attached to the side of the AM8 frame.<br/> I added 3 versions of the case (with a SD card...

This is a remix of the case from Leo_N but i made it completly from scatch... (cause editing a stl file is a pain in the a..) It's designed to be attached to the side of the AM8 frame. I added 3 versions of the case (with a SD card reader, a µSD card...

I created this case from scratch, completely independent of Leo_N's design. I had to start over because editing STL files can be a real hassle. This case is meant to attach to the AM8 frame on one side. I designed three different versions: one with...

Key Features ========== - Reuse of Original Springs and Screws - Keeps Springs in Place from the Bottom and Top - Holds Firmly Glass on the Hotbed - Makes It Easier to Level the Plate - Corners Are Level or Lower Than the Glass Plate So the Extruder...

A custom-made heatbed cable support for the Anycubic Ultrabase heatbed, designed to work seamlessly in conjunction with the Bohrers heatbed holder (https://shop.bohrers.de/heat-bed-holder-anet-a8-und-a6-kommt-in-kuerze.html?language=de), specifically...

Designed for a 220x220x3 mm hotplate (eg Anet A8 / A6) with 4-5 mm cork insulation on the bottom. The study is based on the FT5 713 Glass Corner project by davebpix https://www.thingiverse.com/thing:2702867 but converted to 2mm screws so you can...

A heatbed cable support for the Anycubic Ultrabase heatbed in combination (out of the box) with the Bohrers heatbed holder ( https://shop.bohrers.de/heat-bed-holder-anet-a8-und-a6-kommt-in-kuerze.html?language=de ) for the Anet A8 & A6. Possible,...

Tired of wasting time changing the filament on your Anet A8 & A6, make this simple modification. Changing the filament in my Anet is like trying to thread a needle with your eyes closed. Since you can't see where the thread is going, you have to try...

ITA Tappi per bobine in cartone Printologist EcoSmart RPETG (v1) per supporto Anycubic e compatibili. Nota: da stampare una coppia. ENG Caps for Printologist EcoSmart RPETG (v1) roller. ...

ITA Rullo per bobine in cartone Printologist EcoSmart RPETG (v1) per supporto Anycubic e compatibili. Minimizza gli attriti simulando un cuscinetto. Scalando il modello (senza base) in altezza (Z) è possibile stampare il rullo alla misura...

Supporto elastico x porta bobine Anycubic Rullo per il supporto bobine ufficiale Anycubic, ideale per un facile e veloce cambio di PLA. L'uso della parte elastica assicura una migliore tolleranza alle svariate misure di bobine in commercio. I...

Designing a custom adapter for the E3D V6 proved to be a straightforward process, and I found it essential to replace the inadequate cooler that came with the printer. The unused stock cooler lay idle, providing ample opportunity to create something...

Since I'm not equipped with a standard 30mm fan, I designed a custom adapter to accommodate a widely available 40mm fan instead.

This is a 30mm fan adapter which allows the use of a blower fan. ... This if for cooling the hotend.

I needed extra room for the fan, so I stretched out within the confines of Mount Everest.

Print at your own risk. This works for me somewhat, but an update is expected soon. 20.10.18 Not exactly a remix since it was created in CAD from scratch. However, I give credit where due and acknowledge this design isn't entirely mine. To assemble...

I'm planning to attach two fans directly to the Dovanzeijl X-carriage. Additionally, I'll need a mount for an inductive sensor and a dremel flex arm. Warning: be aware that in version "xcarriage_new7", the x-end switch mount was intentionally...

I'm modifying the dimensions from inches to centimeters on the cover, making it possible to slice it precisely with Cura. ...I'll also obtain the base from Danfuh's original files since they were initially too small due to being in inches.

I created this replacement support for the Front Panel and Y Belt Tensioner found on https://www.thingiverse.com/thing:2242857. This design serves as an alternative to using the "support_belt_tension" and "screw_m8" parts if you encounter noise and...

I designed this model because moisture and dust often infiltrated the extruder, causing problems. This design accommodates 1.75, 2.85, and 3mm Filament. To assemble the filter, you'll need to use a Filament filter on all parts once...