anet a6 3d models

I built a new one that works well, but keep in mind it can still break easily, especially when attaching it to the backplate.

Check out this awesome cable chain design on thingiverse.com - it's a must-see! ...Thing #2001681 is a fantastic project that you won't want to miss, so be sure to head over and take a look.

This is a remixed section reserved specifically for installing a voltmeter.

Ball-bearing holder featuring recesses for 22mm ball bearings.

Modification of the Anet A8, A6 printer's extruder fan for improved ventilation and head access. The stock heat sink is removed to allow proper cooling of the extruder motor. The new fan is mounted on a bracket, allowing maximum airflow into the...

Print Settings: Printer: Anet A6 Rafts: No Supports: Yes Resolution: 2.5 - 3 Infill: 10-25% Notes: Simple supports only for the front and center mounts of the brace rod. Post-Printing Instructions: To mount this thing, loosen the y-belt and four...

Anet a6 e3d clone direct drive with 18mm sensor and flexible filament guide. I didn't find here direct drive for e3d v6 with 18mm sensor without problem for X-stop, so I made a mix of all options I found. I combined the following things into one...

**02-11-2018** Anet recently changed the default A6 power supply at the start of 2018. The STL has been revised to accommodate the change, and still functions for pre-2018 printers. (i.e., some internal features were removed, and the screw hole over...

This thing enables you to use shorter belts in a printer with the traverse bar mounted on the lower side.This is a remix of https://www.thingiverse.com/thing:2782170which is a remix of https://www.thingiverse.com/thing:2347849Update 03.05.2021:Added...

------------------------------------------------------------------------------------------------------------------------ I Wanted to Upgrade My A6 Anet Printer's Hot End to Accommodate Chinese J-Hotend Components. Unfortunately, This Required...

This has slight border on the top to prevent it from sliping out of the suporting hole. Hope you like it Print Settings Printer Brand: Anet Printer: A6 Rafts: No Supports: Yes Resolution: Fine Infill: 50% Filament: Generic PET-G (PLA also works...

Here are the top two options for the A6 with Bowden motor mounts and rear frame braces: Option 1: **A6 Performance Package**: Upgrade to our premium performance package, which includes high-performance Bowden motor mounts and a reinforced rear frame...

This is a bespoke 80x80x25mm fan duct designed exclusively for the Bowden E3D V6 clone configuration on my Anet A8 printer.

Changelog 04/19:\nCarrier\n - Optimizations Made\n\nDesign Released From WIP-status\n\nChangelog 03/13:\n\nPictures Added\n\nChangelog 03/08:\nNew Carrier Implemented\n - Bearing Fix: Circle to Hexagon Changed For Printability\n - Cutout Added for...

As I started modifying my A6 into an AM6, I wanted to use a Titan Aero clone to reduce weight on the x-carrier. I also wanted to include Z-probing with a piezo disc. I'm using the clone from Trianglelabs, and it's working well so far. I took some...

I created this design to address the poor design of the original Anet Extruder, which puts excessive stress on the upper screw and motor mount. To alleviate this issue, I've modified the design so that the upper part is now secured by two guides,...

Printing can be quite challenging. To successfully produce prints with a 0.1-0.2 Nozzle, it's crucial to set the Layerheight at its maximum of 0.1mm. When printing thin walls, ensure you print at an extremely slow pace, approximately 15-20mm/s. Only...

Printing is extremely challenging when it comes to achieving precise results. To overcome these difficulties, consider using a nozzle size of 0.1 to 0.2 millimeters. Layer heights should not exceed 0.1 millimeter for optimal thin wall printing. The...

The Anet A8 and A6 Printer's Thumb Wheel Upgrade A bed level thumb wheel upgrade is available for the Anet A8 and A6 printers, offering improved precision and ease of use. This thumb wheel can be used in conjunction with the original wing nut that...

I'm attaching an action camera like a GoPro to my Anet 3D printer.

A hot bed remix to calibrate your Anet. ...8 x M3 screws

I designed a sleek and understated belt holder for the Anet A8 that achieves the perfect balance between stability and accessibility. Its snug fit ensures the belt remains securely in place without any movement, while still allowing for easy removal...

... exhibit some warping due to its small size and long shape - still, it works as intended. Print Settings Printer: Anet A8 Prusa I3 Rafts: Not necessary Supports: Unnecessary Infill: 10% Design Process SketchUp This model was created using SketchUp.

This is an upgraded version of my extremely simple yet highly efficient adapter for filament spools designed specifically for the spool holder that came with my Anet A8. The old version can be seen at http://www.thingiverse.com/thing:1950461. It will...

http://www.thingiverse.com/thing:2122573 This adapter for filament spools is incredibly simple yet very efficient and I made it specifically for the spool holder that came with my Anet A8. It moves smoothly with just the M8 rod that comes with the...

This creation was crafted using Tinkercad's intuitive tools. ...Modify and refine it seamlessly at https://www.tinkercad.com/things/9fKg1VQ7h5r.

Hey! I just created this design to attach a motor on the left side of your printer. It works incredibly well, trust me. Hi! I designed this mount for a motor, it allows you to place the motor on the left for E3D V6 extruders and it's working super...

This is an assistant screw that helps the filament go through to the extruder. Most of the time when I change filament, and I tried to thread the filament through the extruder it bumps into tube connector. ... UPDATE (01/02/2019): Dimensioning problem...

I'm a helpful assistant screw that propels the filament smoothly into the extruder. ...Typically, whenever I switch filaments, threading them through the extruder usually gets hindered by the tube connector.

I just upgraded my left motor mount and it's a game-changer! ...The new design makes it super easy to load the filament compared to the old one.