anet a8 board schematic 3d models

This board and mosfets holder for the Anet A8, was thought to handle everything inside the boxes, including two types of different mosfets. also function only for the board, with the facility of putting and taking the board simply by sliding on the...

Basically using two rectifier diodes, the Anet board is protected from the higher voltage of the 12 volt sensor, but allows the 5v z limit switch pin to pull to ground when the capacitve sensor senses a surface. I'm using this setup on two Anet A8...

Replacement spacer for mounting my Anet A8 main board. ... Part measures 15MM x 7MM x 3.5MM center hole.

I needed a mount for my breakout board so threw this together quickly. ...Might be useful to someone! Use M3 nuts as a spacers when attaching mount to Anet frame. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 10%

This is an installation board for adding smoother boards to an Anet A8. ...It's for boards like this:...

... to Vampi for additional design advice. I shifted the location on the hole in Circuit Board Cover 2 to align with the reset switch button better on the circuit board. Happy Printing. Print Settings Printer: ANET A8 Rafts: No Supports: No Infill: 20%

Here we have some *reportedly* good firmware for the anet a8 using a melzi board. NOTE: I don't own an anet a8 nor would I ever buy one, therefore I have no actual means of testing this firmware, USE AT YOUR OWN RISK! It has been reported that...

******************************************************************************************************************** Dear designers and makers, On this occasion we have designed a box to house the main board that comes standard in our Anet A8 and...

A simple adapter for changing the original printer board to a MKS Gen 1.4. Original dimensions of the hole spacers included. ...

Actual main board v1_5 Anet A8.

Simple 70 Fan Support for Anet A8 Board. ...

Anet A8 board mounting with M3 spacer for 120mm fan, compatible with AM8. ... Have fun!

Customized version of http://www.thingiverse.com/thing:2733293 I used this to mount my 6-motor RUMBA board to my Anet A8 frame. I left the spacers at 15mm for both inner and outer holes, so I could use the existing screws to mount the adapter onto...

I'm using the steel frame from Orballo Printing and I have not been able to find a compatible holder for the Anet A8 stock board, so I made this. WARNING: The supports for the board itself are not correctly aligned with the board's holes, but with...

Este suporte da board e dos mosfets para a Anet A8, foi pensado para segurar tudo dentro das caixas, incluindo dois tipos de mosfets diferentes. também funcian somente para a board, com a facilidade de colocar e tirar a board simplesmente deslizandoa...

15mm stand off for the Anet A8 Main board I lost one of my standoffs for my printer and had a hard time finding one that could be 3d printed so i made one its simple but i hope it helps people.

Fan cover for Anet A8 Main Board. For 70 mm x 15 mm fan. To secure the cover to the plate, it will be necessary to change the direction of the screws (leave the screw head toward the side of the frame and nut toward the side of the base plate). ...

Anet V1.0 Board Kühlung (80mm Lüfter) / Anet A8 Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: 0,2 Infill: 10-20%

This is a simple cover for the electronics control board of an ATER A8. The cover hangs on the USB port, there is no need for mounting screws. A reset button is included (note the large end of the reset pin should be inside the case). ... Printing...

Please note that i turn my Anet Board and the USB Port looks down on my Printer. ...I also replaced the origonal connector for HotBed, Power and Extruder (the three big green ones) with other: STLZ950/2G-5.08-H...

A mount for the stock Anet board to fit it in the CD-rom slot of a Desktop PC casing to give easy access to the microSD slot and USB-A port. ... I have not yet printed this thing myself and my modeling skills in Blender are moderate at best so don't...

Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Notes: Nothing special needed. I just used the Cura defaults for my printer to print. It took about 2 and a half hours and used about 7m of PLA (20g). Post-Printing...

Case to cover over board The red marked part, are only support and should be cut before used. Please note that i turn my Anet Board and the USB Port looks down on my Printer. I also replaced the origonal connector for HotBed, Power and Extruder (the...

A shelf mount board holder / wire management for my rackmount

This is a simple support for a board's 8cm fan. Simple as possible. ... You need: 2xM4 bolts 2xM4 nuts Enjoy!

Platinen Kühlkanal für einen 92mm lüfter für das Anet V1.0 Board Print Settings Printer: Duplicator I3 PLUS Rafts: Doesn't Matter Supports: Yes Resolution: 0,2 Infill: 10-20%

Update: Feb 29, 2020 V3 of the board should now support BOTH the Anet A8 motherboard and a RAMPS 1.x with an Arduino mega 2560. The Arduino board is positioned to put the USB connector in the back. This is an enclosure for an Anet A8/AM8 build. ...

Wanted to remix this in order to mount my GT2560 board I upgraded to from the Anet1.0 board. I'm only using 1 Mosfet for the heated bed. Adjusted the cover to move the fan positioning to where I felt it adequate to keep the board components cool...

Holder for Anet A8 stock board + BananaPi M2+ + single mosfet.

control board cover for ANET A8 plus under 80mm cooler