anet a8 cooling fan 3d models

The acrylic frame on one of my old A8s was starting to flex enough to push the Y-axis stepper out of alignment and affect print quality. I could go into detail on the engineering and physics of this, but it boils down to these printers needing...

Aluminium Frame Upgrade Power Supply: Power supply Mean Well LRS-350-24 can be found at this link: https://www.thingiverse.com/thing:4116720 The case to pair with it is the SKR v1.3 + BIQU mosfet + 2x 40 mm fan, available here:...

LED Holder Attachments are Available Online at Superbrightleds.com for Easy Installation on Your Printer's Y Belt Screw, Featuring Dimmable and Auto-Off Functionality with the Blower Fan. ... The Miniature LED License Plate Bolt is a Convenient...

... the risk of failure. ... Photos will be uploaded soon, waiting for the case cover to complete printing. My base is slightly altered since this project was custom-made. The case cover has been revised as the holes were too snug a fit for my fans.

... and inevitably knocks it over. ... This is more of an advanced upgrade for anyone who's getting bored with low-risk printing and likes to live life on the edge. It can also be used as a tray or something less cool. ... DO NOT PUT DRINKS ON THIS!

5-The dimensions of the fan installed are identical to those of a typical Pentium 4 fan. 6-Holes have been reduced to improve airflow within the box. 7-Accurate adjustments have been made to the holes allocated for SD and USB. ... 8-Provision has...

After completing the Fan Hinge print job, I realized that I was left without a clear pathway for the filament. Initially, I didn't give it much thought, but as the night wore on and the extruder returned to its home position, my filament began to...

This innovative design empowers users to seamlessly integrate an 80MM PC fan, while simultaneously reorienting the main board from its standard position to provide effortless access to both the USB and SD card slot. For optimal results, M3 hardware...

PCB case: https://www.thingiverse.com/thing:989845 by vtoryh PCB fans (2 fans-40x40mm) plastic parts: https://www.thingiverse.com/thing:1174589 by steba PCB fans grid: stl file is attached Power Supply Case (for 12V, 360W PS):...

PCB case: https://www.thingiverse.com/thing:989845 by vtoryh PCB fans (2 fans-40x40mm) plastic parts: https://www.thingiverse.com/thing:1174589 by steba PCB fans grid: stl file is attached Power Supply Case (for 12V, 360W PS):...

I installed the fan to cool the stepper drivers - most cases come equipped with either a fan or a reset button, so I decided to combine the two protection features in one setup, hoping it meets your requirements. ... Please review the wiring...

I decided to make it minimal for a 12v, 1W LED and tapped power from the fan. This was my first Tinkercad design, so it's quite basic but does its job. ... The LED I used is available on eBay:...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Power Supply Case with built-in Anet A8 Mosfet Holder mount and cooling fan. ...Mounts on an 20x20 with mounts A M3-.50 nut is required.

I combined it with the flip-up fan holder to make changing filament a complete ease. It's been a while since I created and installed this, so I don't recall many specifics. Maybe some minor filing/sanding to get the bolts and bearings to fit just...

The cooling system is less prone to bending, and there's less dust accumulation. One of the biggest advantages is faster print times. Bed heating time has dropped from 20 to 50 degrees in under 1:50 minutes. Here are a few things you should keep in...

This thing was created since I couldn't find a case that would hold two mosfets (of the type I used) and the Anet mainboard. I either only found cases to hold the mosfet(s) or the mainboard; many also had space added for other circuit boards that...

Here are the start and end G-codes: START.GCODE: ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m...

... a direct view of the hotend. I recommend turning off the cooling fan when printing with ABS. You need to replace the 4 M4x8mm screws with 4 M4x12mm. ... (in the renders, you can also see my laser mount) https://www.thingiverse.com/thing:2658897

... a direct view of the hotend. I advise turning off the cooling fan when printing with ABS. You need to replace the four M4x8mm screws with four M4x12mm. ... (You can also see my laser mount in the renders.) https://www.thingiverse.com/thing:2658897

For my printer, I am using a 40x20mm FLX Noctua Fan which is probably the quietest thing you can get away with for higher temperature prints while still maintaining good air-pressure & disbursement. Due to the thickness of the fan, the Noctua...

I believe a power supply that supplies 15A requires only a fan attached or built in, which is essentially a cover for an 80mm x 25mm PC fan.

Airflow System for Ikea Stuva with Airflow Regulation. ...You can completely seal off the ventilation to print ASA or ABS. The cross-section is perfectly adapted to the fan. Fan: be quiet! ...Pure Wings 2 80mm BL044

The fan is adjusted at a precise angle of 15 degrees, allowing for an enhanced line of sight directly towards the nozzle.

Warning: The fan duct hole may need some adjustments for a precise fit if you're using an old fan duct. Although the dimensions should be close, I didn't pinpoint them exactly, so feel free to edit in Tinkercad. Note: An axial fan like the Noctua...

The final product is a compact extruder fan mount that securely holds the fan in place while also providing a clear path for the filament to flow smoothly through the printer's hotend. ... To test the design, I printed it using my 3D printer with the...

Here's a parts list: * 2 M4 screws for the mount cover * 4 M3 screws for the mount * 1 M3 screw with a nut attached like a washer (check the photo) for the fan Changes Made: The fans are now located at the front and extend up to 200-210mm on the...

This way, I don't need to speed them up, and the 5015 fan performs better than regular fans. ... The Carriage Remix is based on @Dousi's design (https://www.thingiverse.com/thing:2203912) and the Clamp remix and duct on @donnyb99's work...

... ...The unused stock cooler lay idle, providing ample opportunity to create something better. I took on the challenge of designing an adapter that would optimize cooling performance, utilizing the existing printer components to their fullest potential.

Improvement of a widely-used fan blower design now includes resizing and an adjustable vertical height feature. Visit https://www.thingiverse.com/thing:1620630 for more information. To ensure optimal airflow, it is centered based on the geometric...