anet a8 lack enclosure 3d models

This is remix for door knobs for Ikea Lack enclosure. ...Because part of the knob was too weak for me so I redesigned it.</p> <h3>Print instructions</h3><p>Print without support and place it on bed to the flattest part</p>

Tool Holder Attachment for IKEA Lack Table Enclosure - Two Secure Screw Spots. Robust Ribbed Base for Enhanced Clamping Power. Compatible with Screwdrivers, Prusa Stock Pliers, and More. ... Print the Tool Holder's Upper Part Directly on the Printer...

I kept losing my calipers, so I needed a place to put them. ... I decided to whip this up so I could put it on the Lack enclosure I'm building. ... Hopefully this rudimentary design helps someone looking for a place to keep their calipers.

Designed to be used in the Ikea Lack enclosure, with the filament spool inside the box.The concept is very similar to that of the Prusa enclosure, with the filament spool inside the box, if you need a filament guide, I've make this remix.I did some...

I crafted this custom enclosure for my Wanhao i3Plus using three Ikea Lack tables. It comprises three distinct parts and hinges for the door. The design bears resemblance to other enclosures found on thingiverse, but I created it primarily as a...

I remixed the Prusa Lack enclosure as the original design doesn't fit a CR-10 Mini. I made some tweaks to the design so it would be a bit more sturdy and modified the doors so they can open on two sides (front and left) to allow for easier filament...

The printer is extremely loud and sometimes struggles to print ABS, so I chose to design something similar to the famous Lack Enclosure. https://www.thingiverse.com/thing:2012384 However, due to the height of the printer, a delta, I created a double...

This design allows you to use the Prusa Lack enclosure as either a standing desk with a high monitor (mine is mounted on the Might Stand https://www.thingiverse.com/thing:1703678) or fold it down for a sitting desk with your laptop screen. The desk...

My i3 MK3 printer basically consist of three stacked Lack Tables ( see link ), where the upper is the modified enclosure and does reside on wheels. ...In order to be able to pull and push it around, I needed handles. I found bwolfey's handle ( see remix...

The original Prusa + Lack enclosure sports a standard filament tube. This setup prints a 16cm slot instead, which raises questions about its design. I adjusted my MK3S by lifting it 1.5 inches off the bottom of the enclosure to add counter weight,...

These brackets are designed for linking multiple IKEA Lack tables that sit at the same level together in multi-printer enclosure setups, helping to minimize vibration and prevent table instability. The screws attaching them to the bottom of the...

Simple tunnel for more cables for your Ikea Lack kind of enclosure. I had to bring power supply for led lights, power cable for raspi running octoprint and power for the printer itself. The only hole that comes with the original enclosure bottom part...

This set of door handles is specifically tailored for IKEA's LACK enclosures, boasting 8mm x 3mm openings at their ends where magnets can be pressure fitted or glued in place to securely hold the doors shut. By incorporating this design element,...

Simple tunnel for more cables for your Ikea Lack kind of enclosure. I had to bring power supply for led lights, power cable for raspi running octoprint and power for the printer itself. The only hole that comes with the original enclosure bottom part...

Constructing the Ikea Lack Enclosure (https://www.thingiverse.com/thing:2212749) required thinner plexiglass panes. To secure the glass, these clever little tools came in handy. OpenSCAD source included to let you adjust the fit for your particular...

Anet A8 3D printer modification. ...Add enclosure for incorporating switch and power cable into the power supply.

It is based on most of the Ikea Lack enclosures out there. But t is made for European thickness panels (18mm). Also it does not have a door, but has the possibility to add an 4 mm plexiglass sheet in front that could be held in place by magnets. ...

I used the existing holes from the original lack enclosure and cut out all the space between them making a slot that is 275mm by 10mm. ...Just used a utility knife to make the cut.</p> <h3>Print instructions</h3><h3>Licence: Creative Commons -...

This is a spool holder I created for use with the IKEA Lack Enclosure: https://www.prusaprinters.org/cheap-simple-3d-printer-enclosure/ I needed a design that would allow me to swap out spools quickly and easily, without having to fiddle with rails.

:) I was having a lot of noise come from my lack enclosure for my ender 3 pro even after adding squashballs because i run some less than conservative acceleration numbers. This design was made because didn't feel like waiting for more squashballs to...

Bracket for IKEA LACK tables can be stacked either from bottom to top or vice versa, forming part of the A2/X enclosure.

Control panel for enclosures from IKEA Lack table suitable for Expandable Steel Sheet Holder. Rocker switches with the dimensions 15 x 10mm can be inserted into the openings on the left. The frames are glued into the two recesses. This results...

Mini filament guide I needed before I add a filament dry box on top of my LACK enclosure. I printed it with supports and drilled screw holes after printing since I kinda forgot to add them while creating, but it's super sturdy. I also added STEP file...

These are particularly useful when using foam board as it should prevent the board from “warping away” from the lack table itself.  Original:This is a remix of the fantastic Ikea Lack Enclosure, but for using foamboard instead of the typical acrylic...

If you want to leave MK3S+ PSU in place in your Lack Enclosure and run its AC cable out the right side, back corner, this is the piece to use (2nd alternative, cable to the left of corner, rather than right). ...&nbsp;The original cable corner can be...

But when I started my lack enclosure for my Ender 3V2 the holder wasn't gonna fit anymore so I designed a way in thinkercad to mount this on the outside of the cabinet. ... I recommend printing this between 30 - 50 infill to ensure it's strong enough...

I designed a custom holder for my new Lack enclosure to support the IKEA Ledare GX53 lamp. You can obtain the socket from the most affordable GX53 ceiling light, "Mesosfär," which costs just 6.99€ in Germany. To print this design, turn it 90° to...

Mini filament guide I needed before I add a filament dry box on top of my LACK enclosure. I printed it with supports and drilled screw holes after printing since I kinda forgot to add them while creating, but it's super sturdy. I also added STEP file...

The problem with the original design was that it didn't account for my LACK table's unique specs - its inner foot width measures 43mm, which is 2mm narrower than what the design called for. ...So, I made some significant adjustments to the foot aligners...

So I decided to create something like the famous Lack Enclosure https://www.thingiverse.com/thing:2012384 But due to the height of the printer, a delta, I created the double Lack enclosure. Basically I joined two lack table, but not one over the...