anet a8 lack enclosure

LED lighting on Ikea Lack enclosure
prusaprinters

Attach the holder withe closed bottom about 6 cm above the top op the lack table, the location ot the top holder can be measured or by placing the lamp to find the correct highedConnect the correct cableside from the dimmer to the desired location...

IKEA LACK Enclosure Hanging Trash Bin
prusaprinters

This trash bin is mounted on the underside of an IKEA LACK table or anything else for that matter. In my Setup it is mounted under the top table because I have no room to spare under the lower one, but it can of course just as well be mounted under...

My Take on IKEA LACK Enclosure
thingiverse

Bought a $9 Lack for cheap but quickly realized access and visibility would be major issues. Spotted some awesome designs featuring removable tops and legs, which made me think about ways to improve the setup. Initially, I considered a 90° cut that...

Plexiglass Trim With Magnets For Lack Enclosure
thingiverse

Aligning the magnets with the Lack leg is straightforward when you leave one magnet attached to the trim magnet and close the door. I chose not to glue the trim together or attach it to the plexiglass. Unfortunately, this left a small gap visible...

Lack Enclosure Ring Light (with Diffusers)
thingiverse

I printed CR\Moriarty's original design and glued the pieces together then screw mounted them in my enclosure. I then ran the LED's (also using hot glue to keep them up the adhesive on the back of the strip wasn't enough so they needed glue tacks)...

Lack Enclosure Ring Light (with Diffusers)
cults3d

I printed CR\Moriarty's original design and glued the pieces together then screw mounted them in my enclosure. I then ran the LED's (also using hot glue to keep them up the adhesive on the back of the strip wasn't enough so they needed glue tacks)...

IKEA LACK table enclosure PRUSA MK3 modification
prusaprinters

I started to make the original enclosure, but very soon I realized, that design of some parts is not the best. The position of main switch on the power supply does not have any sense, it is located back and under table... I wanted to control also LED...

Ikea Lack enclosure for anycubic i3 mega
thingiverse

Feel free to fork or repair this project: https://www.tinkercad.com/things/gpmEDKf1PUN-plexibox-front-right-top-leg https://www.tinkercad.com/things/hp1pVfNPRkQ-sizzling-lappi...

IKEA Lack Enclosure Creality Ender 3 Compilation
thingiverse

Filament Guide: https://www.thingiverse.com/thing:2156762 Handle and Hinges: https://www.thingiverse.com/thing:1920010 Spool Holder: https://www.thingiverse.com/thing:2853619 Lack Risers 85mm: https://www.thingiverse.com/thing:2545125 Filament...

Anet A8 Power Supply Cover - Protection
thingiverse

This custom-made enclosure perfectly matches the specifications of the Anet A8 power supply, boasting a width of approximately 110 millimeters, a depth of about 50 millimeters, and an impressive height of roughly 85 millimeters.

Anet A8 T corner tiny frame holder
thingiverse

An avid creator sought a compact enclosure to house their Anet A8's upper frame, one that would simplify transportation and storage while maintaining access to the machine's essential components.

LCD Enclosure (Wide Version) for Prusa MK3 Lack Enclosure
thingiverse

LCD Enclosure (Wide Version) for Prusa MK3 Lack Enclosure, this is the wide version, Short version here, https://www.thingiverse.com/thing:3432396 W~5.259" D~3.734" H~1.759" Mounts to ceiling of Lack Enclosure Rear Lid, No supports, edges of clips...