anet a8 spool holder 3d models
412378 3d models found related to anet a8 spool holder.
thingiverse
https://github.com/geoffd123/Hpgl2Gcode Other Notes: --Only home your device at z=17mm or higher else you run the risk that the pen holder clips the support. No big deal but annoying if it does. I changed my default start Gcode to move to 17mm first...
thingiverse
- Secure the radial fan to the fan holder using washers and two nuts. - Connect the parts, but don't tighten the screws fully. - Install it on your printer, attach your preferred fan duct, adjust the height, then tighten the screws carefully (avoid...
thingiverse
The general idea is from LucaCap's rear bed leveling sensor holder (http://www.thingiverse.com/thing:1883473). All credit for the fantastic design and idea goes to him! Nevertheless, the original design requires tapping threads into the metal...
thingiverse
This is a remix of hadoko's extruder fan mount with a holder for an 18mm inductive sensor. Now you can have the fan hinge for easy access to the extruder and hold the sensor too. Below are the settings I use for the Marlin firmware. I also added...
thingiverse
Place the fan holder over the remaining piece that's screwed to the metal, put back the extruder motor - it fits snugly. Note: When you put it back, use a smaller screw; I only used one on the left side. When you put it back, cut the left screw...
thingiverse
The perfect accessory for your Tatara Anet A8's robust steel frame is now within reach - a premium top left handed spool holder, specifically engineered to accommodate the popular and reliable E3D Titan extruder. ...This ingenious design ensures...
cults3d
I have designed a spool holder that fits perfectly to the screws of the anet A8 and is perfectly integrated into the machine providing good stability to the filament spool. Just need to add a threaded rod of about 15Cm as a clamping axis of the...
thingiverse
It still has 310x310 build volume, still uses the stock Anet A8 Y carriage so accepts any bed that will fit on that, and has extension parts for a 310x310 bed to be mounted on the original Y carriage. E3D-V6 carriage. For the full 310x310 build...
thingiverse
I replaced my broken rod holder on my Anet A8 3D printer by printing a brand-new one.
thingiverse
Holder for Anet A8 with :BTT SKR mini E3 V3BTT Pix2 Mosfet 30AFilament : Esun PLA+ blackSupport : noInfill : 20%Walls : 3
thingiverse
I decided to create a completely new spool holder design myself with revised measurements and widen it to accommodate the spool sprocket design from Jadames: https://www.thingiverse.com/thing:2067525. It's not too wide, allowing you to reuse the...
thingiverse
This is a filament guide for a selected spool holder designed specifically for the Anet A8 3D printer. ... To access this custom filament guide, visit: https://www.thingiverse.com/thing:1505075 The creator of this filament guide used Tinkercad to...
thingiverse
For Anet 3D printer models: A spool holder with a filament guide.
thingiverse
The user requires a custom-made insert to accommodate the threaded rod from an Anet A8 spool holder, necessitating a compact solution that fits within the device's inner compartment.
thingiverse
Upgraded Spool holder for ANET A8, designed specifically for acrylic frames with an 8mm thickness and stud width of 8mm. For effortless rotation, it necessitates a bearing. I utilized the 628Z bearings, measuring 8x24x8 mm in size. 1. The internal...
thingiverse
Spool holder for the ANET A8 printer. Specifically designed for an acrylic frame that measures 8mm in thickness, and a stud that is also 8mm in diameter. The external diameter of the spool can reach up to 220mm, while the internal diameter of the...