anet a8 temperature sensor 3d models
100540 3d models found related to anet a8 temperature sensor.
thingiverse
This is the single extruder version of my other Anet A8 Carriages here: https://www.thingiverse.com/thing:2766701 https://www.thingiverse.com/thing:2734717 BlTouch version here! https://www.thingiverse.com/thing:2873811 Get the chain here:...
cults3d
This optimized duct maximizes air flow and compensates for the additional distance between fan and nozzle due to the autolevel sensor support found here: http://www.thingiverse.com/thing:1911146 Without this sensor support, the duct might collide...
thingiverse
This duct is optimized to maximize airflow while compensating for the additional space between fan and nozzle caused by this auto-level sensor support:http://www.thingiverse.com/thing:1911146 Without this sensor support, the duct may collide with...
thingiverse
Filament Guide available in three configurations to accommodate a variety of filament sensors.
thingiverse
Soporte para varilla del eje Y para sensor de límite, con diámetro de 8.43 mm
prusaprinters
alternate Sensor holder with more space to access the screws Category: 3D Printer Accessories
cults3d
This is the single extruder version of my other Anet A8 Carriages here: https://www.thingiverse.com/thing:2766701 https://www.thingiverse.com/thing:2734717 BlTouch version here! https://www.thingiverse.com/thing:2873811 Get the chain here:...
thingiverse
... is 7.7 Millimeters. Contact Me for Any Improvements :) Only Suitable for 1.75mm Filament! Print Settings Printer: ANET A8 - Prusa i3 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Layer Height Is Enough Infill: 20% Is Usual for This Project
thingiverse
More info on original thing's page but here's the quick blurb: Main goal of this sensor mount is to bring BLTouch sensor into position where entire bed can be measured for mesh-leveling while giving easy sensor height adjustability without...
thingiverse
When the autolevel sensor is mounted in front, everything goes smoothly except ordinary glass bed clips; they stay on the nozzle's way at the back edge when autoleveling occurs and can be on the sensor's way at the front edge while printing. With...
thingiverse
I used a 12mm Inductive Sensor (LJ12A3-4-Z/BX) so I mounted it solely on the lower mounting bracket because it's too short to fit snugly in both upper and lower positions. The sensor wouldn't have been long enough to drop down into sensing range from...
thingiverse
... worked best for me. It was also a hassle adjusting the sensor height each time. So, I came up with an ultimate solution - Clamp V6Z. The sensor attaches to this clamp using two M3 bolts and 2 M3 nuts, making it incredibly easy to adjust the height.
thingiverse
I've reworked this design to seamlessly integrate with the 3D Touch sensor, bringing it into alignment with modern technology. ...To make this happen, I've included both Fusion360 and STP file formats for your convenience.
thingiverse
The main goal of this sensor mount is to position the SN04 so that the entire bed can be measured for mesh-leveling while giving easy sensor height adjustability without compromising thermal stability with the removal of the heatsink. Height...
thingiverse
... design! ...I'm thrilled to announce that we've just added a brand new mount for a 12mm proximity sensor, perfectly complemented by a sleek 63mm hot end and an optimized fan nozzle. ...This upgrade is sure to take your print game to the next level!
thingiverse
I quickly conceptualized an asymmetrical fan-duct as a solution since the other half-circle design wouldn't work due to the AutoLevel Sensor's obstruction in my setup. ...You might need to fine-tune its height according to your specific configuration.