anet a8 x belt holder 3d models

... of the belt, which in turn decreases necessary tension and vibrations. The following parts are required: - 5 x M3 18mm (from Anet kit) - 5 x M3 nut - 2 x washer (for original pulley) I welcome any feedback or comments. ... Best regards, Brisemuth

This design is tailored for individuals who face similar challenges as I do with X-axis rods, which often prove difficult to position correctly (please refer to the attached images).\nPrint Settings\nPrinter: Anet A8\nRafts: Irrelevant\nSupports:...

... Hex nut * 1 M3 Screw (20mm long) * 1 M4 Hex nut * 1 M4 Screw (35-40mm long) Feel free to print this design and have fun with it! Printer settings for optimal results: * Printer: A8 Anet * Rafts: No * Supports: No * Resolution: 0.2mm * Infill: 35%

... The updated v2 has a larger 11mm opening to accommodate a 9mm teethed idler pulley wheel. These are the ones I used: http://www.ebay.com/itm/301834183849 Print Settings: Printer: Anet A8 Rafts: None Supports: None Resolution: 0.2 mm Infill: 25%

The recess in the casting is 7.6mm wide, while most X-Belt Tensioners have guides that are 8mm wide. In my case, the guides are a bit narrower at 7.5 mm. I drilled holes that are 3 mm deep and intended for M3 nuts and bolts. ... Maybe it will help...

I fashioned an X-Belt tensioner specifically designed to work seamlessly with my X-Axis guide rods, which had trouble seating properly during the initial assembly process. ...Depending on your printer's configuration, this modification might necessitate...

Hi, I made this X belt tensioner. All you need is on the last picture. You dont need longer belt, you have to shorten it a little. There are some imperfection in drawing (It dint print one hole, I had to drill it). I am attaching sketchup and obj...

I was unable to find any tensioners that fit my printer perfectly, so I designed one with a looser fit around the bearing holders myself.\r\n\r\nThe design for this tensioner was inspired by a project already uploaded on this platform (thing...

I'm excited to share with you my creation of the X belt tensioner! Everything you need is clearly outlined in the last picture, so take a look. Don't worry about needing a longer belt; instead, just shorten it slightly to get it working perfectly. I...

Mounting points reworked. ... Fits for the slim belt.

An additional assembly mount for the X-axis is added to this design from https://www.thingiverse.com/thing:2328353, incorporating motor support and tensioner belt tensor. The axis of the tensor has been added with threaded shaft, tensioning nut,...

To complete this task effectively, gather two additional M4 x 3/8" machine screws or longer and two M4 locknuts.

Here's what's new: It's an updated remix, courtesy of viktor3d X Beld Tensioner. What I've changed: - I'm now using M6 x 35 DIN 603 screws. - The sliders are beefed up - they're now 33mm from left to right. - My pulley has shrunk down to fit...

This custom belt holder replaces the standard acrylic components found in the Anet A8's stock setup, specifically designed to support the Y belt.

ANET A8 ANET AM8 Y BELT HOLDER Category: 3D Printer Parts

When creating an X belt holder, you also need to design a Y belt holder since they both broke at the same time last year. This one is built to be more durable than the previous ones. I'm not sure if I installed the "secure" piece properly or if I...

The belt should just fit in and hold itself when tensioned. ...This mount also perfectly aligns and centers the belt on an Anet A8. ...You will probably have to shorten your belt a bit.

Anet A8 X-axis Belt Tensioner Maintenance Tips and Tricks

I'm replacing the belt holder because the acryl ones break quickly. I've tried using originals from Anet, but they're too thick and inflexible. ...To prevent layer shifts, I upgraded to a more flexible and reinforced belt that's suitable for both...

what is parametric: - base plate size [x,y,z] - holder plate size [x,y,z] - holes size [diameter] (placement is centered) - belt width and length to cut the holder plates (self centerd + self place by holder size) - belt slide displacement, to fine...

This is the X-belt tensioner of the Anet A8 plus reviewed and corrected

anet a8+ x-axis belt tensioner reverse engineer of original part

One useful accessory for the Anet A8 is a well-designed belt holder. ...This attachment provides a sturdy platform to keep belts organized and within reach, allowing users to focus on their projects without worrying about loose belts getting in the way.

These files match the original X-axis belt tensioner found in the Anet A8 Plus kit, but I encountered problems with the belt slipping out occasionally on my end so I decided to upgrade the smaller component of the belt holder allowing you to loop the...

It is the same like "Anet A8 X Axis Belt Tensioner" by elmas156 just cool dedicated wrench added :-)

This is essentially a duplicate of elmas156's Anet A8 X Axis Belt Tensioner, but with a sleek, specialized wrench. ...I think it's really neat.

this is a compiled and edited version from several source of Anet A8 plus x belt tensioner works like a charm, just like the original

ANET A8 3D PRINTER X-AXIS BELT TENSIONER INSTALLATION GUIDE. ...WATCH THIS VIDEO TO LEARN HOW TO DO IT: https://www.youtube.com/watch?v=AYvk_e3o5xI

I remixed "Anet A8 Plus X axis belt clamp" from user "nigelayres". I love this clamp but on my Anet A8 (non-plus) the screw holes do not line with my printer a bit. So I edited STL file to comply with my Anet A8 and I also narrowed down belt slot to...

I designed a simple solution to adjust my X belt on my Anet A8 by creating this cam belt holder. The cam fits perfectly in place of the original retaining screw, allowing me to achieve precise tension adjustment through rotating the cam until I reach...