traxxas trx4 rear bumper 3d models
53457 3d models found related to traxxas trx4 rear bumper.thingiverse
I didn't care for the chrome bumpers on my TRX4 Bronco and I couldn't find a rear bumper I liked on Thingiverse. This is what I created to replace my chrome bumper. ... I don't recall what infill I printed it at as I printed it a month or so ago.
thingiverse
I designed this to add extra clearance to the TRX4 Sport rear bumper by removing the trailer hitch mount. I recommend printing it with the rear side touching the build plate. It was a nice snug fit printing as is with ABS, but if you want an easier...
thingiverse
I designed this to raise the rear bumper after I raised the body on the truck. This mount puts the bumper 4mm down from the frame. With this mount and having the front bumper mount flipped, you get a lot better clearance and are able to run the...
thingiverse
Front and rear bumper designed for the Traxxas TRX4. ...Worked perfectly with the Bronco body, and I'm sure it will look awesome with other bodies as well
thingiverse
New rear bumper for TRX4. This maximizes ground clearance over anything else. It eliminates the D-rings and trailer receiver. What it sacrifices in scale detail it makes up for in added rear clearance for climbing near vertical obstacles. I designed...
thingiverse
A thinner version of my other front and rear bumpers for the Traxxas TRX4
thingiverse
These bumpers have been printed and fit the TRX4 Defender. They have been tested on some pretty arduous rock and trail terrain and did not break, even using PLA. ...They have greater clearance for steep climb and descent angles.
thingiverse
I created a new bumper for the Traxxas TRX4. This bumper is more compact but still has the features of the stock bumper, plus the ability to put four 5mm LEDs. D-rings that work on the stock bumper will work on this bumper. I printed this bumper...
cults3d
rear turrets for traxxas trx4 sport high bodies, I printed them with 100% filler, the car has had many accidents and they have never split.
cults3d
SPECIALLY DESIGNED TRX4 SPORT REAR BAR 1 PCS 3D PRINT MOUNTED BY USING M2.5 BOLTS
thingiverse
This is a rear bumper for the Traxxas TRX 4. ...Will fit my custom mount or Madzimo's mount https://www.thingiverse.com/thing:2847515
thingiverse
Good Clearence for crawling Printed With 80% infill 3 perimeters Print face on the bottom For use with TRX4 Sport mount or Bumper Mount by Extance : https://www.thingiverse.com/thing:3622533
prusaprinters
Unscrew the rear bumper bracket and slide the part between the frame rails. Screw the bumper bracket back on. The bolt pattern is off-center, but the winch itself sits squarely in the center of the frame. I mirrored the part to cut the bumper on...
youmagine
EDIT: part has been updated with tighter dimensionsa rear bumper for the 1/10 scale traxxas slashbumper arms can be found here https://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracesupport brace for the rear bumper...
thingiverse
Here is a reasr bumper for the Traxxas Maxx rc truck to match the front bumper.
thingiverse
Designed to adapt Revo style bumper to the Traxxas 4x4 chassis. Fits to the rear diff housing. It currently lacks a mount for the swaybars. ...My intent is to put Summit bumpers on a Telluride and I don't see the need for sways.
thingiverse
Wanted a bumper for my TRX-4 with a Axial Cherokee body on it that would fit in tight to the rear of the vehicle and not hang down very low. I used a bumper mount with very little drop and as far out on the frame as I could get. Added a spare tire...
thingiverse
This is a front bumper mounted LED light bar for the Traxxas TRX4 Sport, though it is pretty much universal so it should fit just about any truck. The light bar is designed in two parts, the clear lens and the housing. The two parts sandwich one...
thingiverse
This is a servo winch solution for the Traxxas TRX4 Sport which fits the original bumper. To built this winch you need - a standard but powerful 360° servo (e.g. JMT 35kg) - typical china winch coil and steel wire: (...
thingiverse
This is used along with a front axle in place of the stock rear axle in the trx4. I have used a shorter servo arm such as the one in the image from losi as well as a tie rod I had sitting around from my bandit drag car conversion. If you print...
prusaprinters
these are the 2 pieces that make up the rear bumper mount on the traxxas slash 1/10 scale 4x4 R/C car. I've included a hitch mount on the top piece as well. Print instructionsUnassociated tags: bumper mount, R/C, slash bumper, traxxas slash Category:...
thingiverse
these are the 2 pieces that make up the rear bumper mount on the traxxas slash 1/10 scale 4x4 R/C car. ...I've included a hitch mount on the top piece as well.
youmagine
bumper mounts for the traxxas slash 1/10 scale 4x4 RC car
cgtrader
Traxxas TRX4 bumper mount for servo winch installation Layer 0.2 nozzle dia 0.4
thingiverse
More info can be found here ---> https://the-ab-outdoors.com/archives/284