anet et4 mainboard 3d models

The Teflon tube clamp securely attaches to the hot end side of the device, providing a stable connection that can withstand heat and vibrations.

I replaced a foam that had burned on the leveling sensor extension, so I created a new one to be printed from scratch. It fits perfectly than the original. ... My settings were: PLA material Layer Height: 0.1 mm thick layers Infill density: 20% solid...

Clips para cables, sugiero imprimir al menos 5 de cada tipo para evitar futuros problemas de organización y gestión.

Habe das Internet durchsucht. Nichts finden können, was passt und funktioniert. Hier nun in rechter und linker Ausführung. ... Mit Fusion 360 lassen sich Kleinigkeiten noch leicht anpassen.

<p>Clips para cables, aconsejo imprimir minimo 5 de cada</p> Category: 3D Printer Accessories

Cover with guide bearing, to make the introduction of the filament easier and avoid wear. Necessary: -1 Self-Locking nut: M4 -2 Washer: M4 -1 Bearing: 624vv -1 Screw: M4*16mm Tapa con rodamiento guía, para hacer mas fácil la introducción del...

Replaced sensor with switch. ...Much easier to adjust the z axis.

The Human Resources Department has implemented a new policy governing material feed guidelines to ensure optimal performance from all employees.

Un simple soporte para poner el final de carrera abajo, con el mismo se puede regular la altura. ...Necesario para el montaje: 2 Tornillos de M5x8mm 2 Tuercas de cabeza martillo para perfil 2020

This piece is straightforward, a shield for our 40x40 mm fans. A 30% fill is more than sufficient. ...Printed in PLA at 40mm/s with layers of 0.18 for a great finish.\r\nIf you have any questions, ask.

Looking at the stock fan duct, it appears to be quite a distance from the nozzle.\r\nWith this modification, you can still utilize the stock fan and achieve improved performance.\r\n\r\nA new revised version has been created, which adjusts the...

The extension is being made to reinforce the stability of the cable arm's hold.

Humans printed out an antique edition using a vintage printer with authentic original hardware components.

I'm enclosing my upgraded design for the filament holder, which provides significant improvements over previous versions that were prone to shocks and fluctuations. I've made several key changes to ensure optimal performance and reliability. The new...

Cover with guide bearing, to make the introduction of the filament easier and avoid wear. ... Required: - Self-Locking nut: M4 - Washer: M4 - Bearing: 624zz - Screw: M4 x 16mm

We dislike the Y cable due to its tendency to bite and come loose. Feel free to modify as needed. It works perfectly for me. V5s models feature a repaired extended final phase, secured with a cover. Only download the V5s version for optimal...

Two decorative pieces for 5015 fans are available, one for the right side and another for the left side. They are made from PLA with a 30% infill. ...The layer height is 0.20mm, no supports are included.

I design and share this filament guide with the community as Groot1598. After downloading and printing it, I encounter a problem where the filament consistently slips off the roller. To resolve this issue, I make some adjustments to the design. ...The...

Looking at the stock fan duct, it seems that is far from the nozzle. With this mod it´s possible to use the stock fan and get better performance. ... New updated version, modified the airflow to redirect to the nozzle.

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Print with Support.\r\n\r\nFor a 25x25x2mm "U" aluminum profile, two units of approximately 430mm in length are required.\r\n\r\nEight M4x30mm screws, three M4x25mm screws, eleven M4 nuts, and sixteen M4 washers are needed.\r\n\r\nA single 608...

It is a practical pulley so that the filament enters straight to the end of filament sensor and thus decreases the friction. ...The sensor's own screws are used.

Here is the rewritten text: A simple support to place the end of the course below, with it you can regulate the height. ... Required for assembly: 2 M5x8mm screws 2 Hammer head nuts for profile 2020

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Added a little flat bit where the knob goes on so it fits better and you can turn it. ...

It is a component that works in conjunction with the filament support, designed to be threaded into the preceding hole. With version 2, there has been an improvement in grip tightness. ... Required: * 1 Nut: M8 * 2 Self-locking nuts: M8 * 1 Washer: 8mm...

Anet ET4 Direct Extruder Upgrade Using Titan Edition Hardware.

Further changes will follow. Sometimes there are only 3D constructions that have not yet been moved. The frame with all parts has been assembled. Weitere Änderungen folgen noch. Teilweise sind es aber nur 3D-Konstruktionen die bisher nicht geruckt...

I'm simply reworking the design to correct an offset issue. The process is enjoyable, and it also helps reduce profile surface usage - this printer has limited space for accessories due to its minimal "free profile" area. ...This modification works...

Adapter plate for the Hemera/Matrix Extruder compatible with Anet ET4 and ET5 printer. ... You will need 2 M3 Insert for the BLTouch Mount.The bltouch mount slide for adjusting the height the bltouch, compatible with V6 and Volcano blocks.