anet et4 mainboard 3d models

Primary layer height 0,16 You need two BALL BEARING 8-22 mm and, naturally, you have to print items as per pictures. ...

Perfectly fitting smoke detector: Ei650 You will need: 2 x Screws for attaching the smoke detector. ... Remix from: Cable Clip: https://www.thingiverse.com/thing:2731180

This is a modified Version of the X-Belt Tensioner designed from “Misterguru” on thingiverse.The edge of the base body, which is in contact with the sheet metal, was moved by 20.3mm. ...In addition, an additional edge has been added to the base body at...

Designed for Anet A6/A8/AM8/BLV converted to 24V with using the hotplate from Anet ET4. 4 mm cork thermal insulation on the bottom of the plate. Based on the FT5 713 Glass Corner project by davebpix https://www.thingiverse.com/thing:2702867 but...

I wanted to use an SKR 2 motherboard in my Anet ET4 so I made this simple mounting system. ...Its a slightly unconventional position but it works well and I was able to use the original ribbon cable, with some new terminations until I get to rewiring...

Esta es una modificación al Hero Me original, se realizo con la intención de adaptar el modelo para colocar un mosquito hotend con los ventiladores originales de la Anet ET4 PRO que es a la impresora que esta dirigida, también se ocupo el acople que...

Just a remix to hold the bed level sensor so you can install a micro swiss direct drive all metal hot end on an ET4 pro. ...This does require a slimmer stepper motor for the extruder.

Anet A8 Mainboard Fan Cover with Integrated Fan Grill for 80mm Fans Added are the 123D Design Files to Easily Modify It Yourself for Smaller Fans

Tired of the leveling sensor failing in my ET4 PRO, so..... Printed the Adjustable Z EndStop, from doublec4. ET5XZtop-mainbody.STL ET5XZtop-thumb.STL Then use a cheap filament sensor as level (it came with the cables), and had to design a...

Anet et5x için kendimin tasarlamış olduğu ücretsiz geliştirme. ...spatula ve yan keski etrafta başıboş dolaşmasın diye böyle bir tutucu yaptım.

I use this as a conversion from side fan to blowing to mainboard directly. I only recommend using this design if you leave the bottom cover open or you might really need the side fan in place to exhaust all the buildup heat. ...It is also you print the...

Here are some upgrades I made to my et4 pro and the cura settings. 1. The cable chain thing is not my design. Here is OG -https://www.thingiverse.com/thing:4372936 2. The lightbar is my design it is designed to go at the top of the printer with...

Soporte para tira Led, Posterior al extrusor Apoya mi canal de YouTube: https://www.youtube.com/c/AmanoNewWorld_Se_Libre

Humans produce items that require additional materials to function properly, such as a base structure or framework. ...This is commonly referred to as having "support" or being "supported." The term "ABS" likely stands for Acrylonitrile Butadiene...

Human: Annettle is a type of flexible tube clamp used to secure cables and wires in place. ...It is typically used on the extruder motor side of a 3D printing machine, where it provides stability and prevents damage to delicate components.

# 需要: * mgn12h滑块+12mm宽导轨长320mm * m4*20内六角螺丝 4个，用于固定y轴两端的导轮 * m5*20内六角螺丝2个以及m5螺母4个，用于垫高y轴电机旁边的两个导轮 * m3*8六角螺丝15个，用于固定导轨，还有热床底板固定在滑块上 # 步骤： 1. 先用“钻孔参考架.stl”，在热床支架上钻四个m3的孔 如果钻孔钻的不准，导致热床底板无法很好的固定在mgn12h滑块上，可以在一边的两个孔扩大为m4的孔。 2.

*CLIP PARA LA CAMA CALIENTE IMPRIMIR SOLO EL STL CON EL NOMBRE: "clip_left" -------------------------------------------------------------- *CLIP PARA LA CARRO DEL HOTEND IMPRIMIR EL STL CON EL NOMBRE: "clip_right" "clip_left" ...

The motor used is the 42SHDC3025-24B model, identical to the original of axis Z1 and the extruder. Axis Z1 and Z2 must be identical. The cable of the new motor connects to the motherboard pin Z2. The pin-out of the new cable must match that of z1 in...

Height increased by 4 mm

this spacer aligns the wire coming out of the sensor which is normally made for a left extruder. ... Note: To use the left extruder, the polarity of the stepper motor must be changed

Modified original mesh. ...Maybe your reset button wont fit, make a hole for it by yourself.

For phones up to 1.1cm wide and for narrower phones, I recommend printing a custom mini holder to fit properly and be stable, as seen in the Sony device photo. ...

Porte lumiere 12v avec support et Roulement à bille de 4.5 pour Laser ou CNC. ... -Sans support sauf Porte lumiere et bouchon -Bille pour roulement = Bille AIRSOFT de 4.5 inox -Impression PLA: -Buse : 200° -Plateaux : 50° -Draft : 0.2mm   -pour...

The Essential Accessory for Your Home Office - Human: An Elegantly Designed Bed Cable Holder Protector

Hello! I'm excited to share a simple upgrade I did a month ago that's been making a huge difference for me. The issue of filament rubbing against the filament detector box was really frustrating, especially since it would often break within the first...

Mod designed to improve the cooling flow as well as to prevent the ducts from knocking down the parts by colliding with debris that is produced. the mod has modular options to be able to use direct drive bmg and the ducts can be adjusted to the...

Conjunto Hotend V6 clon con tensor eje X y guía lineal Disponible para ventilador de capa de serie o 1/2 turbinas 5015 Tornillos necesarios M3x20 M4x25 M3x8 M5x30 Tuercas M3 y M4

The cat is hanging from the back of a bed with its legs open wide.

Support for placing the end of career of axis X shifted to the left and thus gain printing area. It's necessary a T nut m4 and a M4x15 screw. ... I made the holes with a Dremel but a welder would also work.