anet et4x 3d models

Print Settings Printer: Anet A8 Resolution: .1 Infill: 20% Notes: Most pieces were printed at .1 with 20% infill, some others with 5% infill. I will try and document what was what as I proceed to upload the files. There are a few pieces that I just...

Not sure it will be useful for you, but I did not found any hook of the dimensions I needed so I made this one. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.3 Infill: 20% (Gyroid pattern for more 3D strength)...

I have not reproduced the original cap design as it was not very handy in my configuration. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.3 Infill: 20% Filament: PLA Notes: I used 5 lines for the shell to be...

But then it's 3D printed, so I might as well try to compensate for the general fragility related to inter-layer adhesion, hence add more plastic! Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2 Infill: 30...

This mask was designed to be printable on smaller printers with a 220x220 mm bed (like my Anet A8). As the whole mask cannot fit on such printers, I split it into two halves, with the interlocking mechanism which does not need glue (it's based on...

I've mounted my Anet A6 on a Lack enclosure and wanted to mount the PSU and Raspberry Pi externally to protect them from heat. I designed this to allow a USB lead and two pairs of 12 Volt twin cables to pass through safely. There are two versions...

Edges are chamfered so it matters slightly. Picture of servo used has been included for reference. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2 Infill: N/A Filament: Stronghero PETG Black How I Designed...

It holds only on two small parts on top and bottom (see last two screenshots here). Please take the attacher from the original design or from one of the remixes. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.24mm Infill: 30%...

So I removed the "legs" of this holder and glued the printed part onto the filament guide. Print Settings Printer: Anet A8 Supports: Yes Resolution: 0.2 Notes: The initial designer created the holder very tight. The width for example of these...

The fix for me was this cup holder wich screws into the wall so even if I punch my glass in the night it will no longer fall and make a mess. I remixed this model https://www.thingiverse.com/thing:3225373 by https://www.thingiverse.com/TheJadeRabbit...

The model itself was printed using an Anet A8 3D printer, courtesy of some high-quality PLA. To ensure perfect balance, I added just the right amount of lead and modeline. And here's where things get interesting: let's break down the individual...

... on other furniture, let me know if you know! Wheels are 60 mm diameter and 18.2 mm wide. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2 Infill: 10% Filament: Overture PLA Grey Category: Household Supplies

Or a brand new mirror bed for my 3D printer! This model is made for pliers with 10.5 mm wide jaws (13/32" ?), but once you see the concept, you can make your own! Note for the non-initiated: you still need to score your glass before using those!...

Here are now some clips which solve the issue. FreeCAD file included if your batteries needs other tolerances for clipping or if you want to go for other battery sizes. Caesar Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No...

Please reference my Anet A8 documentation: https://www.thingiverse.com/thing:3143558 Note: This document can be applied to any 3D Printer running any controller with Klipper or Marlin FW. ...You will have to adjust the PINS according to your printer’s...

Fits Wonderfully With This Model: Cr10 / Ender 3 And Similar Https://Www.Thingiverse.Com/Thing:2494642 Anet / Prusa And Similar Https://Www.Thingiverse.Com/Thing:1632847 Https://Www.Thingiverse.Com/Thing:2099577 Also Check Out My Other E3D Projects....

Remove individual threads around the lid hooks and any stringing.] Designed with: CAD: Fusion 360 Prints in pictures: Slicer: Simplify 3D Printer: Anet A8 + Material: Inland PETG [Natural] Centipede project information and code can be found at...

... ball bearing for distance.</p> <p>Ball bearing is used. 5mm thick, 5mm axis, 11mm outside diameter. Print Settings Printer Brand: Anet Printer: A6Rafts: Doesn't Matter Supports: Doesn't MatterResolution: 0,3 Infill: 20% Category: R/C Vehicles

Pegs may need to be filed or sanded to remove remaining support material for a proper fit. Check out my other pegboard paint rack for Ammo by Mig paints here: https://www.thingiverse.com/thing:3334508 Print Settings Printer: Anet A8 Rafts: Doesn't...

Please feel free to share this model if you like it and want to support my work that I am putting into creating new designs, you can donate me if you wish with paypal: https://www.paypal.me/JordanHogetoorn Print Settings Printer Brand RepRap Printer...

I'm building a second Lack enclosure for my Anet A8 and wanted to design a custom riser in Fusion 360 to hone my skills. What I came up with was a two-piece riser, allowing me to remove the top portion for maintenance and troubleshooting if needed.

As always make sure your machine is dialed in and your layer adhesion is good. I suggest at least a 1mm wall thickness with 20 to 25% infill. Print Settings Printer Brand: Anet Printer: A8 Rafts: Doesn't Matter Supports: Yes Resolution: .1mm to...

... the way they click and these switches are cheap. In the middle is a WS2812 led. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: Doesn't Matter Resolution: 200 Infill: 20 Filament: Overture PetG Clear Category: Electronics

Materials : - all printed parts - drilled plate with 4x M5 nuts welded (see video https://youtu.be/I0TzMpkRy_k ) - 4X Flanged allen head srews according to your motor (M6x12 or 15 for XC60PG0S i don't know for the Phidget) - 2X Allen head M5x20...

This cowl is meant to be a replacement one for Parkzone's P-51 Gunfighter.Things to tinker with:wall thickness There are three files, one with a wall thickness of 0.8mm, another one with 0.4mm and one solid one for you to experiment with different...

It is also sturdy enough to hold a 12.9" iPad Pro. The hole in the back part is meant to hold your charger cable. See the images for the part print layout I found worked the best. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: ...

I recently bought an Anet A8 Plus. I found a nice model for upgraded knobs for the A8 Plus here on thingiverse by "VIKING_DESIGNER" so I've been using it for my A8 Plus since the day I assembled it. I found Mohamed's knobs far more comfortable for...

I designed this piece to sit on the bikes kick stand pole which is 13mm in diameter. Print Settings Printer: ANET a8 Rafts: No Supports: No Resolution: .15 Infill: 25% Notes: Infill or resolution can be changed to whatever you need. 25% just...

You get full screen touchability but you can't put your tripod upside down (obviously). There is no thread in the screw mount, but forcing a 1/4" screw in the hole is fine and very secure as long as it's deep enough inside the hole. Included is the...

Make sure to check out my design online at Tinkercad, where you can edit it as needed: https://www.tinkercad.com/things/6ckseyNpfMV Here are my print settings: Printer: ANet A8 Rafts: None Supports: Yes Resolution: .08mm layer, 4mm nozzle, 30mm/sec...