anycube photon s 3d models

It allows you to vary the thickness of the spacer.After I tried to install this on my Photon M3 it turns out that the original file can interfere with the linear bearing unless you are very careful. ...I have made changes to limit that potential on both...

This system extracts fumes from an Anycubic Photon printer without replacing existing panels. Instead, it attaches to the rear of the printer over the top of the rear vents using magnets, preserving warranty validity and ensuring easy attachment and...

All parts print effortlessly on Anycubic photon. Due to slight variations in fan sizes, some filing of the inside of the fan box components may be necessary. I used Gorilla tape to ensure fans were securely sealed since exhaust ventilation occurs...

I needed a vent adapter for my new Anycubic Photon Mono X and didn't like the ones already here with the vent pointing straight back so i chose to make my own that's angled to the side. So far there's 4 versions, with differences in screw length and...

Print the object with no centering ring directly onto the plate and the other with support using a printing service, specifically designed for use on a Photon S device.

Another Version of the Genius “ANYCUBIC PHOTON Easy Leveler” by Wundel https://www.thingiverse.com/thing:3096818 In this Review, Only Two Improvements Are Made - Pressure Springs and Insert Positioning The only improvements made to this design are...

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

Another version of the great “ANYCUBIC PHOTON Easy Leveler” by wundel https://www.thingiverse.com/thing:3096818. In this review, only two improvements are notable - pressure springs have been included to avoid holding the plate in place with your...

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

This is my own try to make the vat for Anycubic Photon Mono X, since I wanted to make a drain stand for the Vat. I dont claim that it is totally exact as the original but as close as possible I could make it. If anyone finds anything wrong with it...

This accessory, designed to replace the upper glass of the Anycubic photon printer, will draw in part of the odor emitted by the resin during printing and, with a rubber tube properly connected, discharge it outside. For example, allowing the tube to...

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

This is a z limit spacer for the Anycubic Photon Zero. It allows you to raise the height at which your z limit triggers for the Wham Bam FBS bed. This replaces the current metal bracket that blocks the sensor. The only difference between this and...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

Crafted specifically for Anycubic Photon printers, this platform accommodates the resin tanks seamlessly. Once printing is complete, simply slide the tank into place, shielding the lower area from splashes, scratches, and dust. This way, you can...

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

An Anycubic Photon vat holder is designed specifically to drain resin back into the bottle. The center of the vat should sit directly in the middle of a 1-liter bottle, with the bottle pushed up against the Skadis pegboard. A unique attachment on the...

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

I know, there are some vent systems for the Anycubic Photon already available but I didn't find one that includes a rear fan, which is why I designed this one. ... What you need: * 1 - 92x92x14 mm fan (Noctua NF-A9x14) * 4 - M3 x 16mm socket head cap...

If you're into science fiction, check out a photon torpedo reminiscent of those launched by the Star Trek Enterprise. ...Your feedback is valued!

A precise, three-dimensional depiction of the Particle Photon is available, with the only other version being on SketchUp but unable to be imported.

Wash machine for Anycubic photon mono. Designed to fit any plastic container you can buy. To adapt to your container, you need to measure its width and depth, and then scale the "bearing_axis_(scalable)_2psc.STL" part according to the measured values...

#Description# This is a longer z-stop flag for the Anycubic Photon Mono 4k with the newer version of the build plate arm which has a curved back where it mounts to the z-axis carriage. This z-stop flag is 4mm longer than the original metal piece,...

Adjustable foot for Anycubic Photon

Adjustable foot for Anycubic Photon

This is a custom-made adapter designed for using a 92mm fan in place of the rear panel on an Anycubic Photon 3D Printer. The main purpose of this adapter is to install an activated carbon filter element that draws fumes out of the printer through the...

i desing this angled cover inspired from @scottyujan desing but his was to big for my 3D Resin Printer so it's a smaller piece that works better for my Photon Zero printer. ... i suggest fliping the 3d model to a 90 degree angle for easier printing...

I made this little adapter so that I could use my Anycubic Photon build plate with the Elegoo Mercury Plus. It is a small quick design that can be quickly printer and used. It is designed to reuse the main bracket hardware that comes with Mercury...

This is designed for straining and collecting debris from anycubic photon vat systems. It can be particularly frustrating to go through the straining process after encountering failed prints, especially when the hardened resin is not visible at all...