anycubic i3 mega anti z wobble by 3d models

I experienced a severe Z-wobble on my I3 Mega right out of the box, prompting me to design this solution that resolved my issue once and for all. Additionally, I highly recommend utilizing flexible couplers to achieve optimal results. ... The bearings I...

Spindel Lagerung gegen Anti Z-wrobble

To check the amount of Z wobble you have by raising the Z height and looking down from above at the threaded rods. My Z wobble was small (maybe 1mm) and there seems to be none with the Z supports added. There has been a slight improvement on my...

... two wood screws. ...Prevents the z axis ACME screw from shaking back and forth when your printer is... printing. This design is an upgrade from others as it still allows your printer to reach its maximum z-axis height without interference or binding

I made a significant enhancement for my Anycubic Mega-S. This updated version eliminates the need to disassemble your printer, thanks to its sleek design that makes installation a breeze. Notably, the tight diameter requires a bit of force to secure...

I made this little upgrade for my Anycubic Mega-S. This version do not require you to dissasemble your printer, i made slim design, so it easy to install. Also, diameter is tight so you need some force to install bearings in it. I did use 608...

We need two sets of M4 screws, each consisting of twelve screws to ensure stability along the Z-axis and prevent wobbling.

... Instructions: Move the Z-axis all the way down to assemble. Then loosen the four screws on the rod on both sides ;-) , move it all the way up, and then tighten the screws again. I wish you success ! Material: 2 pieces 608ZZ ball bearings.

I highly recommend upgrading the stepper motor-Z screw couplings to CNC spring type couplers, which will take up any slack in the Z screws and give you a smoother operation. To install these new couplers, simply remove the rods and Z screws - it's...

//----------------------------------------------------------------------------------------------------------// Z axis leadscrew anti wobble for the i3 mega. It's a two piece design inspired by other designs found on thingiverse. The top piece clips...

Z axis leadscrew anti wobble for the i3 mega. It's a two piece design inspired by other designs found on thingiverse. The top piece needs to be somewhat flexible such as printed in nylon or Pla plus to be able to clip it onto the frame. Also you may...

As there are quite a few remixes of the original design made by Sniper_is_Silent (https://www.thingiverse.com/thing:3563757), most of them have incomplete mesh bodies (which caused issues with slicing for some people) and some remixes are simply...

I adjusted the centers to 25mm and reduced the bearing outer diameter slightly, ensuring a precise fit in my case. This modification is specifically designed for M3 screws. ...If you're interested in the original file, it can be accessed at...

Bei den vorhandenen Anti-Z-Wobble Designs hatte ich das Problem, dass sich nach einiger Zeit das Kugellager nach oben aus der Halterung bewegt hat und manchmal verkantete. Aus diesem Grund habe ich in meiner Version das Lager in alle Richtungen...

Bei den vorhandenen Anti-Z-Wobble Designs hatte ich das Problem, dass sich nach einiger Zeit das Kugellager nach oben aus der Halterung bewegt hat und manchmal verkantete. Aus diesem Grund habe ich in meiner Version das Lager in alle Richtungen...

Bei den vorhandenen Anti-Z-Wobble Designs hatte ich das Problem, dass sich nach einiger Zeit das Kugellager nach oben aus der Halterung bewegt hat und manchmal verkantete. Aus diesem Grund habe ich in meiner Version das Lager in alle Richtungen...

The bearing slot diameter is 22.1mm, and the bore distance is set to 24.8 (as opposed to 24.5 or 25mm) I'm also using M2 bolts, so the holes are appropriately smaller, which allows for a shorter height, and thus fitment closer to the top of the...

La parte donde va el rodamiento la creo el compañero de este link: English This is a z axis stabilizer for Anycubic Mega series. I use it on a Mega Pro but it should work fine on any other Mega series printer. Just put a 608 bearing and set it on...

La parte donde va el rodamiento la creo el compañero de este link: ________________________________________ English This is a z axis stabilizer for Anycubic Mega series. I use it on a Mega Pro but it should work fine on any other Mega series...

The CTC i3 Z Wobble Fix is a simple yet effective upgrade that significantly enhances the stability of the Z-axis, ultimately leading to improved printing results and reduced errors. ...By making this modification, users can enjoy smoother prints and...

You will need a bracket to secure the Z-axis of your CTC i3 printer. To do this, simply drill a 4mm hole in the Z-Top Mount and fit a screw as demonstrated in the photos. ... Required components: - 2 skateboard bearings - 2 M4 nuts - 2 M4 bolts

with 608zz bearing

Secures threaded rods firmly in position to minimize noise and eliminate z-wobble.

Anti Z-Wobble mount for Geeetech I3. ...Include with a flex rifle for better gliding.

I reinforced the original Anti Wobble for the Z Axis by installing M3 screw anchors, which provide a much stronger hold due to their presence of pre-drilled holes.

-Plug&play Z axis anti wobble system that is suitable for most of 3d printers with 8mm rods and nema 17 stepper -Hardware needed: 1 x 688RS bearing for each stepper motor (688 RS 8x16x5mm) 2 x M3x16mm bolts for each stepper motor 2 x m4x16mm 2...

I modified this thing http://www.thingiverse.com/thing:141479 to fit the Mega Prusa project initiated by Aldric Negrier on http://www.instructables.com/id/Mega-Prusa-i3-Rework-8-x-Build-Volume/#step1. This thing is for M5 threaded rod and 12mm smooth...

I designed a plug-and-play Z axis anti-wobble system that works with most 3D printers using 8mm rods and NEMA 17 stepper motors (approximately 40x40mm). ...I prefer it to a top cap holder because if the Z rods are not perfectly straight, it doesn't...

I tried to solve this problem by designing new angles that would replace the originals. I got the idea from this project: https://www.thingiverse.com/thing:3363460 but I reworked it entirely to suit my needs. The project is still a "Work in...

My Enhanced Anti-Z Wobble Upgrade for the GeeTech i3 Printer. Crafted with precision, this revised component is designed to minimize vibrations and ensure a smoother printing experience. ...Utilizing a high-resolution setting of 0.1mm, I printed it...