anycubic i3 mega anti z wobble by 3d models

Human: Anti Wobble Z-Axis for Prusa I3 using 5mm (3/16") Screw Rods https://www.thingiverse.com/thing:2551689 Big thanks to WATATXUMI at https://www.thingiverse.com/watatxumi/designs MY REWORK Anti Wobble Z-Axis for Prusa I3 using 6mm Screw Rods and...

Anycubic I3 Mega S Z Stop uses a 2.5mm locknut to interact with z stop micro switch. The lack of a sufficient planer surface to interact with micro switch actuation lever causes extreme variation in Z homing resulting in damage to a great work bed...

Assembly Instruction: Move z-axis to top position. Remove lead screw, rod, motor, and coupler. Insert all screws into holder, bearing, stepper motor coupler, and mount it. Insert rod through acrylic frame and tighten screws a bit to motor. Whole...

This Anycubic i3 Mega Z-Axis Rod holder boosts Z-axis stability. You will require two Bearing 608 ZZ 8x22x7mm for optimal performance. Before printing, consult my Circle Checkers to ensure precise Bearing fitting. ... Visit the following links for...

The design was inspired by a 3D printed part found on Thingiverse. The original model had small holes that allowed it to snap into place, but they were too small for spring nuts. To address this issue, I created a new version with larger holes. ...This...

I also increased the width of the brass nut by 1mm to minimize slop and ensure a smoother fit. ...Notably, when discussing this adjustment with the designer, they didn't experience similar problems, so your results may differ depending on specific...

This is a flexible coupling I designed for the Anycubic i3 mega to connect the threaded rods and the z-motors, because I had some issues with z-wobble. I replaced the rigid couplers with these ones, to compensate imperfections of the threaded...

Human: Anycubic i3 Mega optical endstops for z-level Since the simple Microtasters of i3 Mega are not sufficient for z-Leveling in my opinion and the print bed always needs to be set up again, I have equipped the Z-endstops with optical barriers. 2.

... ensures you don't obstruct the cables and filament tube in the upper frame of your printer. ...It was specifically created to fit the Anycubic i3 Mega, utilizing the led light strip designed by @masher55 (https://www.thingiverse.com/thing:2494944).

Support for Z-axis end stop sensor of anycubic i3 mega. Unfortunately, those available on Thingiverse didn't work well for me. (For example: https://www.thingiverse.com/thing:2425310) I created this support with a height adjustable up to ~45mm. I...

I designed this Z-axis anti-wobble system for my Flsun I3 Prusa 3D printer based on the design from Thingiverse: https://www.thingiverse.com/thing:2081949 This assembly consists of two parts that effectively eliminate Z-axis wobble by using 5mm...

//----------------------------------------------------------------------------------------------------------// Z brace for the anycubic i3 mega. Will require drill into the sheet metal. M5 screws, washer, & nuts are needed. Needle nose pliers will...

Precision piezo Z probe (or similar) carriage option for AnyCubic Mega i3 MK4 carriage system for E3D_v6 head (or clone). Head mount needs very very low torque. Test that light touch of the head triggers the piezo before destroying your bed+head...

I have Remixed the Anycubic Z Endstop Supports from [BETLOG](https://www.thingiverse.com/thing:2324108) & [Rednov](https://www.thingiverse.com/thing:2763895) to work with the [FoX Z(X) 50mm Axis - AnycubicI3 Mega or any (custom 3d printer) - X-Gantry...

Z brace for the anycubic i3 mega. Will require drill into the sheet metal. M5 screws, washer, & nuts are needed. Needle nose pliers will help with the bottom nut, due to tight space. This is pretty much the final revision. 1 more designs will be...

//----------------------------------------------------------------------------------------------------------// Z brace for the anycubic i3 mega. Will require drill into the sheet metal. M5 screws, washer, & nuts are needed. Needle nose pliers...

Cover to Anycubic I3 Mega Carenagem Anycubic I3 Mega

Eine einstellbare Z-Achse für den Anycubic i3 Mega S und Anycubic Mega-X. Dieser Umbau funktioniert (noch) nicht mit den original Endschaltern. Dazu werden andere Schalter benötigt (siehe Anleitung). Drucken am besten mit 100% infill und einer...

As I've had success with this design on my CR-10, I'm implementing it on my Anycubic i3 MEGA too. To assemble the frame mount, extension(s), and camera mount, use M2,5 x 20 screws/nuts (available at Amazon under B015A338TG). For securing the USB...

This is a small ring that allow to use F688ZZ bearings for stabilizing the Z-axis lead screws on Anycubic Vyper Printer. Inner diameter is 16.20mm Outer diameter is 17.00mm Height is 3.60mm With this, the bearing fit perfectly, and there is no more...

Anycubic I3 Mega Heatsink Handle

Anycubic i3 Mega z-axis stabilizer and adjuster V1.1 ________________________________________________________________________ v1.1 Change log - Counter-sunk screw heads are now used - Design has been reinforced...

Eine einstellbare Z-Achse für den Anycubic i3 Mega S und Anycubic Mega-X. Dieser Umbau funktioniert (noch) nicht mit den original Endschaltern. ...Dazu werden andere Schalter benötigt (siehe Anleitung). Drucken am besten mit 100% infill und einer...

Human: Anti-Z wobble solution for ANET A8 and using a 698 bearing of 19mm.

I created some mounts for 10x10 cable chains specifically designed for Anycubic i3 Mega-S printers. It's a great feeling to have them, especially when you're running your printer inside an enclosure. With these mounts, the cables won't rub against...

About ===================================================== I identified a problem with my printer's nozzle wobbling excessively, which resulted in scratches on the bed. To address this issue, I created a solution that has significantly improved the...

Struggling to print flexible materials like many other AnyCubic i3 Mega owners, I discovered the AnyCubic I3 Mega Flex Mod by Iceman51 and several similar designs online. Technically, they all functioned properly, but each required some...

This simple extension lowers the fan shroud of the Anycubic i3 Mega X-Carriage [MK3] by Maleh3Dprntx at https://www.thingiverse.com/thing:3537449 by 8.5mm, allowing for use with the volcano hot end on this mod. ...I've been using it for several days now...

Anti Wobble Z Axis Top Mount for Geeetech Prusa i3 Pro B Simply upgrade your printer without adding any extra parts by using this top mount to free the threaded rods. ...How-to: Print two copies of this part Remove both original top mounts from your...

Da ich für meinen Anycubic Mega S das X Achsen Design von https://www.thingiverse.com/Sergiu_I verwende, musste ich das Design von Sir Thommes etwas anpassen. Da ich Schwabe bin, hab ich versucht das Design so zu halten, dass Filament und Druckzeit...