anycubic i3 mega camera mount 3d models

The Filamentsensor of the i3 Mega holds a Steel Ball and magnetic holder in place. However, theory clashes with practice. Additionally, after modifying the system to use a Titan Extruder, the Sensor no longer fits properly. I extended a holder by...

Summary This frame is designed for the front panel of the ANICUBIC i3 Mega 3D Printer. It can be easily attached to the front panel using some bi-adhesive tape. The main goal of this frame is to cover up the unsightly border around the display and...

This skin fits the i3 mega perfectly and is easily printable on a single color 3D printer. Simply print each component separately, then import them into a slicing software to line up perfectly before printing. The eyes should be printed individually...

... something from AliExpress. It doesn't cost you anything extra, but helps me out a lot :) Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: No Resolution: 0.2mm Infill: 10% Filament: ColorFabb PLA/PHA Blue Gray

... I did not include any mounting holes on the arm of the bracket, this allows it to be more easily used for other camera mounts. ... It is a tight fit to initially snap in place, but once in place it can easily slide up and down on the support.

This is a straightforward spool holder built around the metal tube from the original I3 Mega spool holder.\r\nAssembly requires 2 or 4 M3x10 screws (original screws are too short); I used only 2 screws on the left, and it holds up...

I designed this filament deflector roll because the filament wasn't running straight through the filament sensor in conjunction with a filament holder mounted to the side of my i3. ...I deliberately chose a larger diameter so that the filament could...

I started from https://www.thingiverse.com/thing:2793693 v2019 and needed the mounting holes flipped so I could attach the tray to the right side of my printer due to its location in my apartment. I also enlarged the second wrench slot so that it is...

This RaspberryPi Case for an Anycubic i3 Mega S was adapted and remixed from [Raspberry Pi 3 Case without Vesa mounts](https://www.thingiverse.com/thing:2647012) and [Raspberry Pi case with Pi Camera for...

I'll just get an i3 with a human filter.

Verstellbarer Rollenhalter als Upgrade für den original Rollenhalter vom Anicubic i3 Mega-X, der leider bei mir so rau ist, das schon Filament gerissen ist, weil die Rolle hängengeblieben ist. Die angeschraubte Auflage wurde demontiert und...

If you have converted your mega to a direct extruder, then you need a new plastic feeding scheme. ...This spool holder will help you with this.  Printed in two parts and assembled with 2 M3 screws.

If you have converted your mega to a direct extruder, then you need a new plastic feeding scheme. This spool holder will help you with this. ... Printed in two parts and assembled with two M3 screws.

... I've added a larger nut from a remix and a supplement for the other side. The setup includes a camera mount with GoPro hitch, a separator for the extruder in case the filament is too close, and a modified printer side support to thread the rod.

I am a bit over trying to modify the mega's existing hotend, so this is simply a temporary means of getting better part cooling while printing components for an entirely different printer. I may eventually revise this later, but it will likely be...

Human: This is a straightforward guide for installing a filament support on the ANYCUBIC i3Mega 3D printer.\r\nPrevents Filament Sensor from becoming detached.\r\nThis design leverages existing screws, eliminating the need for extra...

This handheld device enables effortless movement along the Z-axis, effortlessly positioning your camera with precision and accuracy.

Device Mounting Bracket and Fiber Optic Cable Support

to mount a LED strip into the print head 

If you're going to use the standard Titan with the stock Mega extruder stepper, print the SPACER for the endstop - not the SOPORTE_HOTTEND-26mm! You'll need two extra M3 screws. ... For more information, check out these videos at...

Hey Mega Printers, I've mixed and matched some fantastic Solutions to create a brand new Spool Holder that brings out the best in all its aspects. This innovative design boasts three impressive features: it centers the Spool perfectly, rolls with...

This hotend cover matches the exact dimensions as the Anycubic original.\r\n\r\nThe lower section is partially enclosed to prevent cooling air from reaching the plate and the front slots are angled upwards for the same purpose.\r\n\r\nThe fan...

... to different spools. After conducting various trials and failing to find a suitable solution elsewhere, I took matters into my own hands and fabricated my own rollers, which just so happened to fit perfectly onto the Anycubic spool holder frame.

An accessory for standard Anycubic spool holders with ball bearings. You will need: 4 M8 flat head screws with countersunk heads, 16mm wide and 22mm long 4 M8 nuts 4 8mm x 22mm x 7mm ball bearings (inner diameter x outer diameter x width) 8 washers...

I designed this mount to be used with this great camera arm, https://www.thingiverse.com/thing:2568708 ; you can use an M3 screw to make a thread in the plastic or you can embed a nut in it, fits the arm perfectly

Casing for the mounting of two 50 by 50 by 11 millimeter fans at the original power supply unit. ... OR Casing for the mounting of two 60 by 60 millimeter fans at the original power supply unit.

This is a replacement for the cone shaped guide in the extruded, mine fell out and became lost, so I printed this part I designed. ...It will work for the i3 Mega or the Mega -S. ...I couldn’t find anyone else who had uploaded one, so here.

......Mounting screwed to the bearing bolts. The cables of the original length do not need to be extended. For mounting in the housing, you can drill an additional hole or glue the chain on a double-sided tape or glue. ... Resolution 0.18 Infill 50%

... a custom mount that fits perfectly onto the end of the sensor feeder. ...To secure it, simply push the mount upwards until you hear a distinct clicking sound - this indicates it's securely in place. ...Then, attach the screw to finalize the attachment.

The LED module mounting is roughly set so that it shines directly onto the extruder. The mounting is designed so that it doesn't block any of the extruder fan vents. The mounting is done on the factory screws of the fan, which makes it easy to do. I...