anycubic i3 mega mainboard 3d models

I took a distinct approach to quieting and cooling my i3 MEGA-S by emulating how rack mount servers direct cool air over the electronic components and expel warm air out the back of the chassis. By doing so, the entire motherboard and components are...

This fit exactly on my i3 Mega with an Ultrabase and 8bit Trigorilla. You need to print two of each. ... You can use only the feet without the holder and stick some felt pads under them or use double-sided tape to stick the holders into place and stick...

I also hoped it would increase the Z print volume, but unfortunately, the I3 Megas frame still manages to get in the way. The current Z limit is about 140mm. I recommend using my PTFE lined extruder with this mod because it's designed to work in...

To create a more efficient cooling system for the i3 MEGA Ultrabase, consider using a rear 40mm fan as a blower duct. Additionally, you may want to replace noisy fans in the base with quieter alternatives. I used two Scythe Mini Kaze SY124010L fans...

Verstellbarer Rollenhalter als Upgrade für den original Rollenhalter vom Anicubic i3 Mega-X, der leider bei mir so rau ist, das schon Filament gerissen ist, weil die Rolle hängengeblieben ist. Die angeschraubte Auflage wurde demontiert und...

If you have converted your mega to a direct extruder, then you need a new plastic feeding scheme. ...This spool holder will help you with this.  Printed in two parts and assembled with 2 M3 screws.

If you have converted your mega to a direct extruder, then you need a new plastic feeding scheme. This spool holder will help you with this. ... Printed in two parts and assembled with two M3 screws.

... something from AliExpress. It doesn't cost you anything extra, but helps me out a lot :) Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: No Resolution: 0.2mm Infill: 10% Filament: ColorFabb PLA/PHA Blue Gray

Human: This is a straightforward guide for installing a filament support on the ANYCUBIC i3Mega 3D printer.\r\nPrevents Filament Sensor from becoming detached.\r\nThis design leverages existing screws, eliminating the need for extra...

If you're going to use the standard Titan with the stock Mega extruder stepper, print the SPACER for the endstop - not the SOPORTE_HOTTEND-26mm! You'll need two extra M3 screws. ... For more information, check out these videos at...

Hey Mega Printers, I've mixed and matched some fantastic Solutions to create a brand new Spool Holder that brings out the best in all its aspects. This innovative design boasts three impressive features: it centers the Spool perfectly, rolls with...

I also enlarged the second wrench slot so that it is the same size as the other one because the 2 wrenches I got from Anycubic are both the larger size handle. ... I have provided 2 files: 1 is the same as the v2019 from the original tool tray posting...

This hotend cover matches the exact dimensions as the Anycubic original.\r\n\r\nThe lower section is partially enclosed to prevent cooling air from reaching the plate and the front slots are angled upwards for the same purpose.\r\n\r\nThe fan...

I designed this filament deflector roll because the filament wasn't running straight through the filament sensor in conjunction with a filament holder mounted to the side of my i3. ...I deliberately chose a larger diameter so that the filament could...

An accessory for standard Anycubic spool holders with ball bearings. You will need: 4 M8 flat head screws with countersunk heads, 16mm wide and 22mm long 4 M8 nuts 4 8mm x 22mm x 7mm ball bearings (inner diameter x outer diameter x width) 8 washers...

... to different spools. After conducting various trials and failing to find a suitable solution elsewhere, I took matters into my own hands and fabricated my own rollers, which just so happened to fit perfectly onto the Anycubic spool holder frame.

This is a replacement for the cone shaped guide in the extruded, mine fell out and became lost, so I printed this part I designed. ...It will work for the i3 Mega or the Mega -S. ...I couldn’t find anyone else who had uploaded one, so here.

I am a bit over trying to modify the mega's existing hotend, so this is simply a temporary means of getting better part cooling while printing components for an entirely different printer. I may eventually revise this later, but it will likely be...

The Anycubic on Boot talks to the wifi module with AT commands at 115200bps, sends an AT command to switch at 2.250.000Bps and opens UDP server in port 3000. This is a sniff traffic on port, commands sent from Printer. Boot printer and it sends at...

I did install the upgrade kit for the I3 Mega (TITAN-Extruder and Filament-Rack) - the kit is really worth checking out: https://www.amazon.com/gp/product/B07KLJJYNV/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1 But the filament holder falls...

I tried to find a spool holder for my i3 mega but did not end up with one that worked as I wanted, so here we are again and designed one that was more suited for what I need. So I wanted a roller model and after the first few prototypes, I ended up...

After swapping out the fans on my i3 Mega, I decided to tackle other sources of noise as well. The result is my Silent Filament Guide, expertly paired with my Spool Holder. Thanks to the PTFE tube inside its housing, it won't generate unpleasant...

This is a replacement for the mainboard fan mount of the Mega X. It is made to hold a Noctua NF-A9X14 PWM, but another fan with the same size (92 mm), hole spacing (82.5 mm) and a maximum height of 14 mm might work as well. The fan mount is...

I used a previous chain design as inspiration; I believe it was this one: http://www.thingiverse.com/thing:1735193 Print Settings: Printer: Anycubic Mega i3 & Omega i3 Rafts: No Supports: Yes Resolution: 0.2 or 0.3mm Infill: 20 or 30% Notes:...

I'm using it on my custom Anycubic I3 Mega, but it should work on all types of Prusa printers with this mount: https://www.thingiverse.com/thing:926794. The fan duct isn't ideal, but it works. Unfortunately, it's not as good as the stock one. If I'm...

Things you'll need: 2pc 50mm x 50mm x 10mm fans 12V (Important: i3 Mega is 12V) 1pc Y cable XH2.54 female to 2x XH2.54 male (I crimp two wires to 1 connector pin but you can solder the wires) 4pc M3 x 12mm screws 2pc M3 x 5mm screws (can use the...

There should be no interference problems now, assemble onto the existing fan bracket and it should work fine.Things you'll need:2pc 50mm x 50mm x 10mm fans 12V (can search for 5010 fans online)1pc Y cable XH2.54 female to 2x XH2.54 male (to use power...

Nozzle cooling duct for Anycubic i3 Mega. ...

Fan duct for Anycubic i3 Mega printer.

Anycubic i3 mega aeration & anti vibration system