anycubic i3 mega stepper driver duct by 3d models

Direct airflow over stepper drivers in Anycubic I3 Mega by ducting it out the side of the base is crucial. The internal duct clearance is generous, allowing for aftermarket stepper drivers with oversized heatsinks to fit comfortably. This design...

Please see the remixed file.\r\n\r\nThis mod combines Juha's original Anycubic i3 Mega Stepper Motor fan duct and self_taught's 5015 fan mount, with a redesign from scratch.\r\n\r\nWhat's the difference?\r\nA longer bottom tube where the fan mounts...

The air will then not directly exit the housing after the stepper drivers have been cooled but instead will be redirected to the board and chipset that would not be cooled with the original. I have also made it a bit slimmer in height at the end in...

A fun duct for cooling a stepper driver for anycubic i3 Mega S

A better system to cooling the Stepper driver of Anycubic i3 Mega S with radial fan 5015

A better system to cooling the Stepper driver of Anycubic i3 Mega S with radial fan 5015

Based on https://www.thingiverse.com/thing:2846144, I designed a fan holder with a protrusion that fits into a fan's hole, and also an air duct that fits to the fan holder. (not a remix) I used PETG, so the fitting of the fan holder and the air duct...

This is a variation of the fan duct for the Anycubic Mega I3 fan duct. I wanted to suck fresh air from the bottom of the printer instead of inside the box, so made this. Unfortunately, my printer was already modded with very tall heatsinks on the...

This is a variation of the fan duct for the Anycubic Mega I3 fan duct. I wanted to suck fresh air from the bottom of the printer instead of inside the box, so made this. Unfortunately, my printer was already modded with very tall heatsinks on the...

No matter if you're using a stock stepper motor driver or an upgrade like 5 TMC 2208 Drivers (one of the best improvements you can make for this noisy printer, and it's budget-friendly!), the dimensions are the same. Here's a universal guide for...

Custom Stepper Driver Cooling Duct for Anycube i3 Mega UltraBase. Visible on the picture, TMC2208 drivers are installed with their wires reversed at the motherboard connectors. ... Crafted an even better version:...

For additional information, please refer to the detailed description below: Summary: A specially designed Stepper driver cooling duct specifically engineered for use with the Anycube i3 Mega UltraBase. ... As shown in the accompanying picture, TMC2208...

This fan duct is nearly identical to the original Remix by Cover1987, a stepper driver fan duct designed for 50mm fans. The main difference lies in the reinforced area where the fan mounts, allowing users to attach it using simple wood screws. I...

I plan to reduce the duct's height so more airflow is directed towards the steppers. 2. I intend to replace the stock 50mm fan with a better and quieter one. 3. The design will be revised so that the blower blows directly over the main board. ...It...

... by roundisfunny on Thingiverse. ...Take the original funnel from him and utilize this component instead of the ending-piece. If it won't fit into your Anycubic, shorten the bar spacer as illustrated in the 4th picture or edit the part before printing.

So I've created this remix where the fan is held in place by snap fits, eliminating the need for any screws altogether. I haven't printed it out yet, but I plan to do so soon. ... If you're quicker than me, let me know whether the snaps function as...

Update: V2 for Cura users - Since manual support placement is not possible, this version incorporates built-in struts within the fan duct's neck, allowing the entire item to be printed without supports. These struts can easily be snapped off with...

Holder for stepper driver fan on an Anycubic i3 Mega-S. ...The holder is for two 40mm fan.

Human: Anycubic i3 Mega 5015 AIO Stepper Cooler Duct System.

5015 AIO Stepper Cooling Duct for Anycubic i3 Mega

Anycubic i3 Mega Stepper Driver Fan für alle gängigen 120 mm Lüfter Verwendung auf eigene Gefahr, der Designer übernimmt keine Haftung! Das abgebildet Blech (Edelstahl 1.5 mm) kann käuflich für 15€ + 5€ Versand innerhalb Deutschlands erworden...

For cooling the mainboard and the motor drivers. Bracket for 2x 40 mm fans e.g. Noctua NF-A4x10 FLX or NF-A4x20 FLX, also works with any other 40 mm fan. The holder can be attached to the two original mounting holes for the fan holder, you can also...

Hi, I've got an i3 Mega UltraBase with TMC2208 drivers, and I designed a duct for it over on Thingiverse - https://www.thingiverse.com/thing:2773533. It worked okay until I upgraded to Marlin 1.1.8. With the new firmware, I was able to hit higher...

Stepper mount Anycubic i3 mega

Anycubic i3 Mega Filament Driver This filament driver and protection system prevents filament from dropping off the spool when retracted multiple times in a row. ... It works with: * Side Extruded Support (Thingiverse ID: 2448418) * Spool Holder...

Dieser Stepper Driver Cooler wird mit einem 40x40mm Axiallüfter betrieben. Die Stützstruktur ist im Objekt integriert und muss nach dem drucken entfernt werden. Es ist kein Support via Slicer erforderlich! Ich habe es mit der Schrift nach unten...

This Stepper Driver Cooler runs on a powerful 40x40mm axial fan.\r\nIts built-in support structure gets automatically detached after printing, eliminating the need for any additional support through your slicing software!\r\nThe model was...

Stepper driver cooler skr 1.4 turbo, Anycubic i3 Mega , Fan 50x10mm

I took the fan duct design from "roundisfunny," modified it to accommodate a 50x50 fan, hoping it would provide enough or even more airflow than the original 40x40 model. To minimize turbulence and noise, I added rounded features within the flow...

My Innovative Design Leaves the Stepper Area Exposed, Including Sockets, to Promote Efficient Air Exchange Between the Upper Surface and Heatsinks Through a Strategically Designed Air Tunnel. Thin Parts Construction Prevents Pressure Buildup Around...