anycubic kobra max tuning 3d models

Just center your test model on each placing square and delete the layout helper.Added a second version that helps to lift all models in one go.I've also included the “M3 8x layout.scad” OpenScad file for tuning for another printers, just change the...

The tool is employed specifically for growing peas, not for conflict resolution.

Tasarlayan:Oktay Samet Kaz

This is my submission to the SilverStone wall-mounted headphone stand design competition, a collaborative effort with Linus Tech Tips. To support my entry, simply download and share it widely. ...For more information on the competition, check out Linus'...

This is the added, thicker end Z-Axis mount that i mentioned in my "Update" message. The V3 files are 7.5mm thick at the end. They are also rounded to look better. The V4 files are 10mm thick at the end. ...They are also rounded.

Annoyed by a display that’s too bright and you can’t turn it off? With this dark mode, only two holes remain open to control the temperature while using Octoprint. ...Also protects the display from your cat.Print as you like, I recommend 100% infill and...

A more streamline and practical take on PTFE-wire clip.A simple PTFE tube - wire clip. Worked better then some other solutions in my case. Looks cleaner.Optimized for 0.8 nozzle. Will work fine with any other.Step and F360 files are also...

I remixed this PSU-Cover, to fit in Noctua 80x25mm Fans. The original Part2 is also included here, to download it easier. ... Please read the instructions from the original creator, he made a pretty good job!

This is a remix to add a cable guide for the Z axis. Print the parts as they are. No need for supports. Don't hesitate to ask me if there are any modifications to be made.17 part for Z15 part for XIl s'agit d'un remix pour ajouter un guide-câble pour...

<p>This fan duct wraps around on 3 sides to give as much cooling as possible without obstructing the view of the nozzle. There is a thin, removable strip of material spanning the front opening to allow a brim to be used without the brim entering the...

This is an elevation of the printer to be able to use, for example, a higher power supply and mainboard coverage. Furthermore, the feet stabilize the entire printer, which results in a cleaner print image. The feet are put over the original rubber...

I was getting a lot of dust from hollow and cardboard spools rotating above the plate so I created this to use instead. Makes the spool practically have zero resistance, eliminated cardboard dust and works with plastic spools as well. ...Print the...

This box will fit into standard X-Rails to hold extra pieces of filament/drips.

This is my first remix of a piece for my printer, and I made the modification because I couldn't find any mod for the cape fan that I liked, this version is the best so far, I deleted the other 2 because they weren't right, so People do not download...

This little bracket is for mounting a bowden tube to the filament sensor for an external dryer or when you have a cabinet and would like to have the roll outside the cabinet. STL has a M6 x 1.0 thread pitch for the PTC (Push To Connect) connector. (I...

This is a mount for the LED strip profile. The lighting is controlled by the Zigbee RGB light TuYa TS0503B controller. This allows you to automate the lighting of the printer according to your preferences. The lighting can turn on when the printer is...

I Designed this to attach to the two bottom bolts on the print head carriage directly behind the hot end. when installed correctly it will stay just above the tip of the hot end and light the whole area at the print head. I ran the wires for the 2-...

Once you printed the two piece you will need:-2 M4x8 bolts.-1 M4x30 bolt and nut-2 F688ZZ Flanged Radial Ball Bearings (cheap at Amazon)

I got tired of the two previous versions having a 60 mm offset on x-axis. This is my attempt at remedying that.PLA will work, but PETG is better. ... It might be ugly, but hopefully it works.

A very dirty remix for mounting the filament guide with runout sensor. I use underprice sensor in less than 1 dollar fron Ali https://www.aliexpress.com/item/1005003397498506.html instead $15 for original sensors. ... Find the way to secure sensor...

Strain relief cable clips for the X-Axis.FreeCAD Version:Link branch FreeCAD - Version: 2024.123.0.14555

This is a simple remix to swap the mount to the other side, and lengthen the x-distance to accommodate a larger fan on my setup.

I designed this enclosure as a replacement for the original fan, intending to install a more noise-efficient 120mm fan. ...In order to accommodate the larger fan, it's necessary to extend or replace the existing feet.The cover is designed to utilize the...

0.8mm tolerencesyou may will need to trim the bad overhangprinted with no supports10% infill

I decided to remix my V2 mount so that a Wyze V3 camera could be mounted instead. The mount is designed to fit over the X-axis tensioner so that it will travel up and down with the printhead carriage. It allows for a constant side view of the...

Wanted a nice way to keep the filament sensor close to extruder but allow the top mount spool. Tweaked shape to fit around screws not found on Vyper model. Can reuse screws but will need one screw to hold down the filament sensor. ...Provision for a...

I use support blocking on all holes.The shunt mount cover is not finished. I did some trimming after wires were attached. Still working on that. But, for now, zip-ties work wonders! ...lol

<p>The VKD15 is designed to hold 2 5015 blower fans. ...The led wire can be run through the hole in the face plate under the hot end fan or glued in the cutout in front that hole.</p> <p>The idea is to be light weight, this is why the arms are designed...