anycubic leveling 3d models

This design is a Z axis leveling support compatible with the Anycubic Kobra measurements to facilitate the adjustment of the eccentric nuts and avoid printing problems. ... Este diseño es un soporte de nivelación del eje Z compatible con las medidas de...

The test will give you the probe height, assuming the printer's height is accurate and Z equals zero at bed level. If it's off, M48 won't provide useful values. For example, after M48 finishes and displays a mean value of 24.4, set the offset with...

https://www.thingiverse.com/thing:3249319 I have adjusted the following settings: -the bed size -the endstop logic for the hot bed -the default settings from the original Mega X firmware -alternatively with adjusted acceleration settings Enter M420...

A mount that fits onto the AnyCubic Mega Pro (and printers in the same AnyCubic family). It lets you install a digital tire depth gauge of the type commonly sold on Ebay, AliExpress, etc. Gives you another option for bed leveling. Print it on its...

Human: Anycubic i3 Mega optical endstops for z-level Since the simple Microtasters of i3 Mega are not sufficient for z-Leveling in my opinion and the print bed always needs to be set up again, I have equipped the Z-endstops with optical barriers. 2.

I would suggest printing with a layer height of 0.2 mm instead of the current 0.3 mm. ...Additionally, printing two layers of the wall is not sufficient as it results in noticeable distortions from the internal ceilings.

Please do not use this part, it hits the rods in certain angles! ... New version available here : https://www.thingiverse.com/thing:2783157 *********** This part is a remix from https://www.thingiverse.com/thing:2391808, modified with an edited hole...

Just four screws to install and the wheels will be set up, making adjustments significantly simpler due to their considerable size.

Have fun with it! Do you like it? ... I would be very pleased about a tip!

I upgraded the GordTheRogue Probe Mount to accommodate an 18mm sensor, carefully designing it to avoid interfering with the rods and eliminating the need for supports during printing. ...This customized mount is now securely fastened to the Kossel...

Kept finding the knobs on my Mega S came undone very easily so i decided to design these they accept a M3 nylon nut. ...I used a mug to press them in (it was quite a tight fit) and made sure to put some super glue inside to make sure they don't come...

Hi, Remix of https://www.thingiverse.com/thing:3145976 by MKingCharles. Originally, this design lacked numerical details. To address this, I incorporated numbers into the model. During printing, I inserted pauses in the G-code and seamlessly...

This is a spacer that needs to be positioned between the foundation components on either side and the vertical axis modules. ...Its length measures precisely one hundred millimeters, which streamlines the horizontal alignment process of the z-axis...

I made this replacement when my Z leveller on my Anycubic Photon Mono X broke - There is a Z offset spacer as well in case you need it to add height when installing a magnetic plate for your print bed or if you have a Z offset problem on your printer...

Calibration check model for Anycubic Predator printer bed (360x360x1mm).

This is a levelling removable bracket based on the design found at https://www.thingiverse.com/thing:1976680 for attaching a Pushbutton to the Effector on an Anycubic Kossel printer for bed levelling. It is designed specifically to fit a 7mm thick...

I need a custom rework of that mount to fit my wider sensors. ...20mm will be perfect.

Made to fit a DM3-02P micro switch precisely. Dimensions are 12.8mm x 5.8mm x 6.5mm. A slight reduction in height of 1-2mm on the side where the lever is situated would be beneficial. This adjustment ensures that the frame does not collide with...

... venture. The designed duct is specifically crafted for the original 40x40x10mm fan on Anycubic Chiron, capable of eliminating the "hair" that appears on the left side of the 3D print due to the single-directional airflow from the original fan duct.

You can remove the fourth side to still attach the bed leveling sensor. Unfortunately, I couldn't test the fan-duct design yet because my Chiron is broken, so feel free to test it yourself. Before installing the fan duct, I recommend positioning each...

I couldn't get on with the original even though it's a great design. The threads proved to be too finicky and the mount plate separated easily from the threaded bolt part, likely due to subpar ABS material quality. Nevertheless, I made several key...

Ersatz für die Standard-Einstellraeder des Mega Pro. Die Skala erlaubt das einfache Einstellen bei der Verwendung unterschiedlich dicker Druckplatten auf einem magnetischen Heizbett (Steigung vom M3-Gewinde ist 0.5, d.h. eine volle Umdrehung...

Another way to remedy this is to uncheck origan at center if your slicer if the slicer has this option available to you.  Reference Material:  Brim Test Explanation Video  How to Fine-Tune Z-Offset on a 3D Printer | ANYCUBIC 3D Printing –...

This is a Caliper mount designed to level your Heatbed on the Anycubic i3 Mega printer. Versions: Messschieber.stl is the Click-In Version Calliper mount.stl is the Hang-In Version Messchieber V3.stl allows for movement along rods The Hang-In...

... I used Octoprint to verify my leveling. Print Settings Printer: Anycubic Kobra Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0,2mm Infill: Thunder/Lightning Filament: Anycubic PLA Black Category: 3D Printer Accessories

Even better bed leveling mount can be found here: https://www.thingiverse.com/thing:3158524 This design requires only a few M3 bolts and M3 hex nuts. The mount is meant to replace Anycubic bed mounts, eliminating the need for metal parts and using...

A Support to thighten the screws of the Z-Axis and support the weight of the Extruder, accordinbg to the Leveling of the Bed. I had the problem, that the weight of the Extruder pushed the right side of the Z-Axis-Bar down when i tried to tighten the...

This is a remix of the Creality Stand Tool Holder by pika28. After upgrading the printer, there was no space to attach the toolholder. So I wanted to create a separate one. The model consists of several parts that can be changed later. The top...