anycubic mega x 3d printer

I designed this X-axis belt tensioner to fit onto an Anycubic i3 Mega S because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with no modifications necessary to the current fixture. No need to...

...... I designed this **X-axis belt tensioner** to fit onto an **Anycubic i3 Mega S** because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with **no modifications necessary** to the current fixture.

I was already looking at an EZR for my Ender 3Pro so when i found this bracket I decided I would remix it for the EZR as I want to go direct drive on my Mega X but the other options were expensive. I have tested fitment of the EZR on the bracket, but...

Ho disegnato io personalmente perchè la scheda del sensore della Anycubic i3 mega s,non si trova più o almeno non sono riuscito a trovarlo da nessuna parte... se si installa la sua vite originale, la staffa che va a sbattere al pulsante del sensore...

A remix for the popular Anycubic i3 Mega  with BMG direct drive front plate.This can be screwed in the carriage.Instructions:1. Screw in the top screw in the 180 degree orientation. (vertical)2. Screw in the BMG extruder with the V6 hotend and motor...

A remix for the popular Anycubic i3 Mega with BMG direct drive front plate. This can be screwed in the carriage. Instructions: 1. Screw in the top screw in the 180 degree orientation. (vertical) 2. Screw in the BMG extruder with the V6...

Hatchet remix to add BLTouch support using the original Mega X-Carriage [MK4] bracket. ... Ignore the poor modelling slicer errors, slices great with Cura 5.1 - Cover Plate includes BLTouch mount - X Carriage adds threaded insert hole missing in source...

This is a replacement for the mainboard fan mount of the Mega X. It is made to hold a Noctua NF-A9X14 PWM, but another fan with the same size (92 mm), hole spacing (82.5 mm) and a maximum height of 14 mm might work as well. The fan mount is...

... extruder. ... This is one of few options I have seen for making the Mega X direct drive without losing either X or Z axis capacity. ... Currently using this with my own fan design and this X belt tensioner https://www.thingiverse.com/thing:4908450

Modified astroaaron's file a bit. ...Moved the top holes in a bit as they didn't quite line up on my Mega X. ... Added an arm to mount the filament sensor to so it could also guide the filament from a standalone spool holder a bit better.

I couldn't find a Raspberry Pi Cam mount for the Mega Zero / Mega Zero 2.0 that matched exactly what I wanted, so I designed it myself. You can attach the arm to the motor of the X Axis. For this you only have to remove 2 of the screws, and with...

The complete installation for Anycubic I3 Mega: https://www.thingiverse.com/thing:2860786 EDIT 1: Second model (V2s) uploaded with reduced pins, might help to uncouple or couple the chain elements. The single chain element was uploaded too. EDIT 2:...

took the X axis tensioner and made a version to go on the Y axis of the anycuic mega zero 2.0 Stock pulleys, bolts, and nuts can be used. I added a couple thin washers but if you tighten the bolt going through the pulley it should work fine without...

This is a lightweight foot for an Anycubuc Mega X (dont know if it works on different types). So I am able to remove the base plate entirely to have access to the components from time to time without screwing all together. I think the fans run...

All the common PSU custom covers for the Anucubic I3 Mega that can fit a 92mm quiet fan are not compatible with the slightly longest PSU found in the Mega X, so this cover solve the problem. It can be attached with the original screws to the PSU and...

(NOTE: For the Mega X, not for Mega S.) Since the cable for my rascam is very short (see encircled cable), I had to shorten the clamp/move the camera position (also removed the edge) as well as moved the case attachment closer. I did kept the...

https://www.thingiverse.com/thing:3249319 I have adjusted the following settings: -the bed size -the endstop logic for the hot bed -the default settings from the original Mega X firmware -alternatively with adjusted acceleration settings Enter M420...

Dragchain Holder for X Axis of i3 Mega (Ultrabase, mk4) The smaller part attaches to the hotend and the bigger part goes to the stepper motor of the extruder. Two cable ties secure it in place. Using this setup may result in a loss of maximum Z...

I had attempted several cable chain mount models for my i3 mega, but they either didn't match the 10x20mm cable chain I purchased off eBay, so I created this one myself. It likely uses more filament than necessary, but I'm satisfied with its...

... from https://www.thingiverse.com/thing:398515 Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.15 Infill: 20% Filament: Prusament PETG Grey Notes: Any material does the trick. ... Category: 3D Printer Parts

This camera mount is bolted together using 4 to 5 M3 machine screws, four of which are highly recommended. ...I've successfully completed multiple timelapse projects with this configuration, resulting in exceptionally high-quality footage.

remixed the hex nut version for bltouch with 19mm bearing holes for 10mm rod This is a remix from https://www.thingiverse.com/thing:398515 Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.15 Infill: 20%...

###Ein Z -Halterung für Anycubic. Die man einfach an der seite eingesteckt werden kann ( ohne schraueben oder kleben). ###A Z -bracket for Anycubic. You can simply plug it in on the side (without screwing or gluing). ... <h2>Die LEDs sind 10w, aber...

... c'est plus facile a régler que du noir sur du noir. j'ai utilisé ce tuto pour tendre la courroie : http://nitocris.over-blog.net/2019/05/impression-3d-tension-des-courroies.html l'entre axe fait 35cm, ce qu'il fait une résonnance d'environ 73Hz.

Hello, I've recently got an Anet A8 3d printer from my friend to fix it up. His nozzle was clogged so I wanted to buy a replacement and oh my good they are so expensive in my country so i decided to use my e3d v5 hotend and whole mk4 carriage system...

This system is tailored to complement my innovative modular X carriage concept.

I try to change the 01_X_Carriage.stl to a rod wide of 45mm instead of 50mm. ... Remix of https://www.thingiverse.com/thing:3537449 File 01_X_Carriage.stl It is not testet

Bei diesem Modell können Sie Ihre Webcam an der X-Achse montieren, damit Ihre Kamera der Druckhöhe folgt.

This is my simple modification of Pablo's amazing X axis cable chain that just slides on and lets you keep the original filament sensor.

This is a straightforward tweak to Pablo's incredible X-axis cable chain design, allowing the original filament sensor to remain intact while sliding smoothly into place.