anycubic mega x fan upgrade 3d models

Remixed case for PSU dedicated for Anycubic Mega / Mega-S. It is fixed to use 14mm thin fan from Noctua ( http://s.click.aliexpress.com/e/bslt9qjA ) Holes position and its sizes has been fixed, added extra grid to make whole cover stronger. Also...

Remixed case for PSU dedicated for Anycubic Mega / Mega-S. This remixed case is specifically designed to work with the Noctua 14mm thin fan. The holes' positions and sizes have been revised, and an extra grid has been added to make the entire cover...

I designed this X-axis belt tensioner to fit onto an Anycubic i3 Mega S because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with no modifications necessary to the current fixture. No need to...

...... I designed this **X-axis belt tensioner** to fit onto an **Anycubic i3 Mega S** because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with **no modifications necessary** to the current fixture.

took the X axis tensioner and made a version to go on the Y axis of the anycuic mega zero 2.0 Stock pulleys, bolts, and nuts can be used. I added a couple thin washers but if you tighten the bolt going through the pulley it should work fine without...

(NOTE: For the Mega X, not for Mega S.) Since the cable for my rascam is very short (see encircled cable), I had to shorten the clamp/move the camera position (also removed the edge) as well as moved the case attachment closer. I did kept the...

Fan duct to install on main board of a Anycubic i3 Mega S. Modification of the original source was needed to install properly 2 Noctua Fans NF-A4x10 FLX and prepared to insert M3 bolts and nuts, giving enough space to the steppers heat sinks. Also,...

This design should fit Anycubic i3 Mega and Mega S printers. However, it's crucial to note that it's not compatible with the latest version of the board featuring an integrated SD card reader and fixed motor drivers. Initially, I thought I could...

Just a very simple bracket to mount a common 60x10MM fan for the mainboard in an Anycubic Mega S. Uses stock hardware locations, clears original stepper drivers. No major disassembly other than removing the bottom plate of the printer is required.

https://www.thingiverse.com/thing:3249319 I have adjusted the following settings: -the bed size -the endstop logic for the hot bed -the default settings from the original Mega X firmware -alternatively with adjusted acceleration settings Enter M420...

Custom Stepper Driver Cooling Duct for Anycube i3 Mega UltraBase. Visible on the picture, TMC2208 drivers are installed with their wires reversed at the motherboard connectors. ... Crafted an even better version:...

You Need: For mounting the linear rail: 35 cm linear rail, mgn12h Nuts: https://www.thingiverse.com/thing:3050607 Getting Rails aligned: https://www.thingiverse.com/thing:2368837 The parts of the Petsfang, this version:...

Dragchain Holder for X Axis of i3 Mega (Ultrabase, mk4) The smaller part attaches to the hotend and the bigger part goes to the stepper motor of the extruder. Two cable ties secure it in place. Using this setup may result in a loss of maximum Z...

Please see the remixed file.\r\n\r\nThis mod combines Juha's original Anycubic i3 Mega Stepper Motor fan duct and self_taught's 5015 fan mount, with a redesign from scratch.\r\n\r\nWhat's the difference?\r\nA longer bottom tube where the fan mounts...

Complete Hotend Cover including half-circle print cooling and a mount for a LED strip. Fits the original Anycubic "BOOSFAN JD4512M12" and any 40 x 10 mm fan for extruder cooling, in my case the Noctua NF-A4x10 FLX. Noctua NF-A4x10 FLX (12V, not 5V!)*...

The screwholes allow for some up- and down adjustment to get the perfect height above the part. For mounting the fan to the duct a m3x25 screw and an m3 nut are requried. To mount the fanduct the hotend has to be rotated by 90 degrees so that the...

This is a Remix of the Anycubic i3 Mega-S dual side fan duct by kb-elmo. I liked this design because it matches the sharp lines of the rest of the printer, but it had modeled supports in the duct which blocked airflow a lot. I edited it in...

I made this dual sided fan duct as a slightly improved / better fitting version of the original dual-side fan duct made by H_Run. The original one had some fitment issues on my printer (the fan shroud was too big and too far up). I also changed it...

Now my Anycubic I3 Mega Hotend Cover (V1) has been in use for almost a month. Despite its prolonged usage, the cooling air supply still falls short when printing overhangs on small areas per level. To address this issue, I designed the V2 model, but...

Remixed to mount the fan directly onto plate/cover with the housing from original. (Noctua 92x14 in the case. Fan should be mounted on the OUTSIDE. ...

###Ein Z -Halterung für Anycubic. Die man einfach an der seite eingesteckt werden kann ( ohne schraueben oder kleben). ###A Z -bracket for Anycubic. You can simply plug it in on the side (without screwing or gluing). ... <h2>Die LEDs sind 10w, aber...

Anycubic i3 Mega Fan Upgrade Kit

Anycubic I3 Mega fan mounting bracket for standard-sized fans.

It fits the original Anycubic "BOOSFAN JD4512M12" fan and any 40 x 10 mm fan used for extruder cooling, which in my case is the Noctua NF-A4x10 FLX. The Noctua NF-A4x10 FLX fan operates at 12V, not 5V. You can find it on Amazon DE at...

I have recently upgraded my hotend to the dragon hotend and found that some mods were needed to make it fit. ... I modified the cover a bit to accomodate for larger head and paired with this plate someone else remixed: ...

This system is tailored to complement my innovative modular X carriage concept.

I had attempted several cable chain mount models for my i3 mega, but they either didn't match the 10x20mm cable chain I purchased off eBay, so I created this one myself. It likely uses more filament than necessary, but I'm satisfied with its...

I try to change the 01_X_Carriage.stl to a rod wide of 45mm instead of 50mm. ... Remix of https://www.thingiverse.com/thing:3537449 File 01_X_Carriage.stl It is not testet

Bei diesem Modell können Sie Ihre Webcam an der X-Achse montieren, damit Ihre Kamera der Druckhöhe folgt.

For additional information, please refer to the detailed description below: Summary: A specially designed Stepper driver cooling duct specifically engineered for use with the Anycube i3 Mega UltraBase. ... As shown in the accompanying picture, TMC2208...