anycubic mono x build plate 3d models

anycubic mono x heater stand

this is a remix of another design rotated 180 degree and made to sit on the right side. angled to drip into resin vat. ... resized for a easier fit.

SUPPORTO PER COLATA RESINA ANYCUBIC MONO X ANYCUBIC MONO X RESIN CASTING SUPPORT

New version for ANYCUBIC MONO X VAT lid.

It's a foot for an Anycubic Mono X 3D printer Vat. ... Works for Mono X, Mono X 4K, & Mono X 6K.

2.8mm Z-Axis spacer for the Anycubic Mono X 6Ks to work with the Wham Bam Flexible Build System for Resin (FBSR). Just unscrew the two machine head screws under the Z-axis sensor paddle. Insert your printed piece (in resin or with FDM) then replace...

This drip hanger is designed for the Anycubic Photon Mono-X monochrome LCD resin printer. It is intended to be installed permanently (no need to put it on or take it off for printing or drip function). It allows one to print, then shift the build...

This is an OpenSCAD version of the original Anycubic Mono X Wham Bam Z axis spacer by Elantris. ...It allows you to vary the thickness of the shim.

This is a Build Plate holder for the Anycubic Photon Mono, which rotates the plate around both axes as I have only found others which rotate the plate around only one axis.

This is a basic handle for the Anycubic Mono X. Use 3M double sided tape to adhere to the lid. Sand the bottom of the printed handle for better adhesion. ... I used 3M auto adhesive tape.

This is a basic handle for the Anycubic Mono X. Use 3M double sided tape to adhere to the lid. Sand the bottom of the printed handle for better adhesion. I used 3M auto adhesive tape. ...

Drip bracket for Anycubic Mono M5s Because of the very aggressive drip angle, if your print is too big, might not fit on the bracket. ...

Inside the MONO X the Z-Axis extrusion penetrates the plate and leaves a gap just below the lid sensor - if this isn't sealed fumes from the build area are pulled down by the fans housed in the base and are explelled into the room the printer is in....

drainer Anycubic Photon mono xthere is no need to remove the screw because it passes without any problem

drainer Anycubic Photon mono xthere is no need to remove the screw because it passes without any problem

This is an OpenSCAD version of the original Anycubic Mono X Wham Bam Z axis spacer by Elantris. ...It allows you to vary the thickness of the shim.</p><p>The original model can be found here: <a...

I wanted to get a magnetic build plate for my Photon Mono M5, but WhamBam only had it for the M5S. After a bit of research, and determining that the build plates are the same size, I decided to give it a try, and it seems to work perfectly with this...

This is a station to use Anycubic Photon Mono X remotly. You can send files directly to the printer and watch while it's printing. ... This project has 2 boxes: - for Raspberry Pi Zero W -for Raspberry Pi Camera Install...

Accessory rail for the Anycubic Photon Mono X. Print top and bottom separately. Combine with flathead M5x0.8 10mm screws. Rail mounts are 17mm apart, 6mm wide. Mount accessories with flathead M5x0.8 20mm screws. Freecad files included. Holes will...

this Photon Mono X exhaust is desined to fit and extract air from the sides of the machine, taking away toxic fumes

Soporte para drenar la placa de impresion de Anycubic X 6Ks.Support for draining the Anycubic X 6Ks printing plate.

CAD model of the Mono X lid to use for customization. ...Fit tested a ring on my printer, validated by using this model to create a tight-fitting spacerso a heater cable can pass under the lid.

These allow you to use "Workhorse Safety NIOSH P100" filters (The adapter seems a little different from the 3M adapter.) to assist in cleaning air for the Anycubic Photon Mono X. It all does limit the airflow, but ideally improves the air quality. ...

https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside the vat when you put something on the dripping holder and to shove the build plate and the dripping rack back onto the arm. ...

https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside the vat when you put something on the dripping holder and to shove the build plate and the dripping rack back onto the arm. I...

It works with mono x.Top and bottom are the components of the tank. Print both and glue together with resin and cure with UV.The cap is scaled down of 0.05 to better fit without applying force.Be careful to remove the tank from vat as the resin will...

CAD model of the Mono X lid to use for customization. ...Fit tested a ring on my printer, validated by using this model to create a tight-fitting spacerso a heater cable can pass under the lid.</p> <h3> Print Settings</h3> <p><strong>Rafts:</strong></p>...

&nbsp; Laying the Z-Axis at a 45º Angle leaning on its back yielded me the best results.I painted the front screen with blue testors paint, and then the black screw knob for the build plate in black, otherwise just clear coating the colored resins on...

Don't you just hate it when during manipulation of the build plate a resin drop lands on the outer edge of the vat, finding its way between FEP and glass ?This design adds a large rim around the front of the vat.Two versions are available, the full...

you don't have to worry if your printer has enough resin anymore. ...works with original Anycubic resin bottle.