anycubic mono x 3d models

This is a R_E_R_F test file for the Anycubic Photon Mono. All the ones I found out there took a while to run, so in the interest of saving time and resin, I created a R_E_R_F file that is heavily inspired by the ResinXP2-ValidationMatrix_200701...

It is what it is

Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP. Instructions: 1. Remove the bed plate. 2. Take an old support piece with a flat...

Remix of https://www.thingiverse.com/thing:4640934 MonoX build plate model by mrfumetsu. Adjusted the size of the build plate to 202x128mm. In the original model the build plate was 220mm wide (typo when designing?). ... The other parts -...

Works well. This is the final version where i made improvements over the original designs. It now has 10mm fillets on all of the corners and the lid cutout is angled 10 degrees to sit level when in use + .1mm larger so the lid will slide in a bit...

<p>Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP.</p> <p>Instructions:</p> <ol> <li>Remove the bed plate.</li> <li>Take an old...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Remix of https://www.thingiverse.com/thing:4640934 MonoX build plate model by mrfumetsu. Adjusted the size of the build plate to 202x128mm. In the original model the build plate was 220mm wide (typo when designing?). ... The other parts -...

Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP. Instructions: 1. Remove the bed plate. 2. Take an old support piece with a...

this is a remix of another design rotated 180 degree and made to sit on the right side. angled to drip into resin vat. ... resized for a easier fit.

This is interceptor arm replacement that lowers the arm about 2.6mm for FBSR or 3.8 For XTR from Wham Bam System for the alt version of the anycubic 4K. should be printed laying flat not vertical at .2 mm layer height. ...

I wanted to get a magnetic build plate for my Photon Mono M5, but WhamBam only had it for the M5S. After a bit of research, and determining that the build plates are the same size, I decided to give it a try, and it seems to work perfectly with this...

I looked for a drip bracket on thingiverse and did not find one so I made one myself with help from a friend. The fit on the lift mechanism is quite tight I would maybe shave of 0.5mm off from one of the long inside parts. But some sanding did the...

A remix of Sabacc's original, with the screw holes located in the correct positions.

4/16/2021 - v2 - Updated design to maximize the drip spot to the upper right corner and to allow taller prints. Will also test this. Please leave a comment below if this works okay. This is a remix but with a 5 degree angle to the back. ...Resin drips...

This holds 2x VATs (blue and black). Print with a darker color to deter sunlight. Use PETG filament for the door hinge 'bolt'. I've included the Fusion360 file for easy customization. Kindly leave a like or whatever.. ...LOL.

Thanks to @SnopSnapi for the excellent model and sharing the CAD.  I was  able to import and quickly add some countersunk holes for M3 fasteners to hold the lid more securely.I attached with M3x10 SHCS and M3 Locknuts on the inside of the lid/cover...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Did you buy the most affordable SLA / resin printer? Did you discover the FEP film was incredibly difficult to replace without purchasing a costly pre-perforated FEP? I did. I designed this stencil to solve that problem. ...Simply use some paper...

Replacement of standart single-use film frame for use common FEP film You need: - 28 countersunk screws M3x6 - 28 nuts M3 - Glue for nuts

I broke mine while replacing the FEP sheet. So for now I only have this part. Tried it on a 90mn print, no leaks. I had to widen the holes for the screws, so I redesigned it. ...Please contact me if you notice anything that needs improvement.

2.5mm spacer for optical eye trigger arm for when you fit a magnetic bed. ...Not fancy, not a thing of beauty but does the job.

This holds 2x VATs (blue and black). Print with a darker color to deter sunlight. Use PETG filament for the door hinge 'bolt'. I've included the Fusion360 file for easy customization. Kindly leave a like or whatever.. ...LOL.

Customized version of https://www.thingiverse.com/thing:3911914 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3911914

refuerzo de paredes

It fits perfectly on a 1L bottle (at least on mine) and with a good balance, my bottle does not fall over.

This bracket holds the build plate vertically over the vat, tilted slightly forward and inward to recover resin drip at one corner.

This is an adapter to tilt the build plate after the print to let trop off uncured resin.The V2 you can find here.

I made this to help remove more resin from my prints. It seams there is still so much resin on the models after printing even though it has been hanging upside down for a while. This clamp holds the platform at a 90 degree angle from the vat. This...