anycubic photon mono x 3d printer

Badge for wash and cure and mono X

This is a resin protection dam to protect the Anycubic Photon Mono X build platform screws/mounts in the center from being flooded with resin when being immersed into the VAT. Screws are cumbersome to clean, therefore I made this protection...

Damper Feets for Anycubic Photon Mono 4K --------------------- Simple damper feets for PhotonMono 4K (maybe also fit on a regular PhotonMono)

This is a reinforced 3D printed frame for the Anycubic Photon Mono. ...I have created it when I've broken my original part, and I've figured out that it takes 40 days to get a new one :)

Coordinate system changed for Formware 3d

ANYCUBIC Photon D2, Mono, Photon Mono 4K,Photon Ultra, 2pcs FEP Film frame.

Spacer to lower the Z axis sensor for Anycubic Photon Mono ( Not Mono X ) when used with a Wam Bam Flex plate. ...2 Versions, one has a 1mm drop and one has a 2.56mm drop to account for the full thickness of the Wam Bam plate and Magnet.

You can print it on your photon mono, or on your traditional FDM printer :) Here is a simple to use and easy/quick to print holder for your Anycubic photon mono printer (4K in my case). All you have to do is remove the top knob, insert the holder,...

... cut cable tie or even resolder it. It is up to you.For better result you could also seal the printer main lid joint with sealing tape or some other sealing materials. Printer Brand: AnycubicPrinter:  Photon Mono SE Category: 3D Printer Accessories

Simple vat cover for the Anycubic Photo Mono M5s resin printer.

... Anycubic Photon Mono. ...It should let excess resin drain off. The suspension is inclined on two axes so that the resin can run off over a corner of the printing plate. It is designed so that the cover of the Anycubic Photon Mono can still be closed.

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

Hot news (from comment): Anycubic 4K new firmware at their website, and included RERF file After few days searching RERF file for my brand new Anycubic Photon Mono 4K, i found nothing :( So i decided to make my own file based on XP2 Calibration from...

Wanted to make a handle for my Mono X and Wash & Cure station that I like the look of so threw this together. ...Attached with a bit of double sided tape and printed at 0.2mm with supports on my Ender 3 V2.

2.5mm z-axis separator for the anycubic photon mono 4k. ... The distance from the center of one circumference to the other is 8.5mm, the circumferences are 3.5mm Required if a flexible platform is to be used

anycubic photon mono resin vat lid other accessories: https://www.thingiverse.com/thing:4923162 https://www.thingiverse.com/thing:4912997 https://www.thingiverse.com/thing:4923159 https://www.thingiverse.com/thing:4923146

I was looking for a cover for my vat but only have my Anycubic Photon Mono 2 (no filament printer).All the lids I found were to large (even angled).So I used Tinkercad to remix one.I split one in half, added some height to the center, and then added...

Hot news (from comment): Anycubic 4K new firmware at their website, and included their RERF file, so my design should work still fine but time step changed After few days searching RERF file for my brand new Anycubic Photon Mono 4K, i found nothing...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

It simply hang to the printer itself.Printing: PLA, no spécial think.Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/Print...

This is a vertical hanger for the Anycubic Photon Mono M5S. I am assuming it would also work for the M5 too. ...This hanger is really only good for prints with a built plate to top height of about 80mm or less, otherwise it may drip outside of the vat.

Build plate drain platform to support the latest model of ANYCUBIC Photon Mono 4K with Die Casting Cantilever. The hanger has been designed to clear the resin vat and does not need to be removed in order to print. ... Version 2 has been modified to...

Simple damper feets for Photon Mono 4K (maybe also fit on a regular PhotonMono)

Wanted a lid to cover the resin vat of a Photon Mono SE.

This is the DIY carbon filter for Anycubic Photon Mono SE. It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the...

Hello, I have created a screen cover with hinge for Anycubic Photon Mono 4K, so that at night the light from it does not annoy me when I sleep. The thickness is like this because I used black resin from Anycubic and it came out that in this...

:-)__ ---------------------------------------------------------------- Inspiriert durch das Design "Anycubic Photon VAT Lid by KayIOA" habe ich einen Deckel für den Resinbehälter meines Anycubic Photon Mono entworfen ... mit einem Logo. Im ersten...

With this you can be sure you only throw away absolutely empty bottles :) This was made for Anycubic Photon Mono 4k - I don't have meassurements of any other models to confirm if it would work there. Feel free to remix for your model. It was also...

Simple angled Photon Mono Build Plate holder. ...Heavily inspired by this design for the Photon Zero: https://www.thingiverse.com/thing:4224960 Modeled in TinkerCAD.

There seems to be no hanger for photon mono 2 existing in Thingiverse at the moment, so I created this.