nes controller port 3d models
117248 3d models found related to nes controller port.thingiverse
I remixed a NES Controller port I found here on thingiverse and made a hole for a female USB port. Pushed them together with a bit of heat and they fit perfectly. Hopefully someone else will get some use out of this. ... Added v2 which sits flush...
thingiverse
Even with a heat gun set to 700 degrees F, I found it difficult to push cheap USB extensions through the original part. ...I'm super grateful for the design, and I've modified only slightly to have a 7.3mm x 14.9mm aperture in the center to push my...
cults3d
I needed this for my Nes Pi ;-) http://dcnigma.eu5.org/?p=696
thingiverse
I needed this for my Nes Pi ;-) http://dcnigma.eu5.org/?p=696
thingiverse
I found this parts on the internet, the SNES version came from http://www.raphnet.net/ in .STEP format, and the NES was given to me by /u/ubermeisters on reddit. I had to modify both of them so that they would print with a 0.4mm extruder (which is...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9FeyJk8loUf It's designed to be used with the [WiiChuck I2C breakout board](https://todbot.com/blog/2008/02/18/wiichuck-wii-nunchuck-adapter-available/), which...
thingiverse
Update: Version 2 (Slightly Modified for better fit on all parts) So there's a few designs out there for NES USB Controller Ports, but they weren't quite right. So I remixed them and made one that should replace the existing port and allow a female...
thingiverse
To keep the original appearance with the controllers, you can replace the long wire from original Famicom controllers with a NES controller extension corder, cut into desired length. 2P microphone pin is populated on an N/C pin, if you want to...
prusaprinters
So here is the solution to scratch that itch. 3D model slicer examples as shown in the pictures for best appearance/structural strength. To keep the original appearance with the controllers, you can replace the long wire from original Famicom...
thingiverse
A printable NES Controller (decoration only) Two variations, one with cutouts for buttons, one without.
sketchfab
nes controller modelled in 3ds max and a first demontration of PBR texturing in quixel
sketchfab
Nes controller completed for my college course 512x512 albedo, normal, gloss
sketchfab
Low poly NES controller for school project. ...800 tris, 512 texture sheet, PBR, Quixel.
grabcad
A simple attempt at creating a model of a NES controller. ...Drawn to correct scale.
sketchfab
High to low poly bake of a NES Controller, modelled using Blender and textured using Substance Painter. ...First completed model.
thingiverse
A model of a classic NES game controller. Is scaled down to miniature version. ...Buttons do not move.
sketchfab
Detailed Low-Poly NES Controller. ...My first attempt at using Substance Painter and baking a high-poly onto a low-poly.
thingiverse
For my first 3D object I decided to make a NES Controller. I have drawn it to scale. ...Hope you enjoy!
sketchfab
This is my attempt at making a low poly NES controller in Blender 2.8. ...The total number of tris came to 1,362; most of which is the result of trying to get the bevelling right.
sketchfab
My first non-tutorial project for Blender was making a full NES control deck and controller set. It’s been sitting around a long time because I was too lazy to make the plug, but I decided to finish it off today. ...This is just the controller by...
sketchfab
For my Fda Game Art course, our first task was to model an NES Controller, as well as texture it, whilst abiding to these limitations: - 512 Albedo x1 - 512 Metallic/Roughness x1 - 512 Normal - 800 tris I used 3DS Max to model the controller, and...