anycubic sd card 3d models

... work, but do not fit at all on my 4MAX so i re did the model from scratch using FreeCad. ...For installation i use the same screw that hold the front panel, enjoy it no more sd cards hanging all over the place. ...if you make it please post it, thanks.

To assemble it, I simply used the same screws that hold the front panel in place, and now my workspace is much neater with no sd cards cluttering up the area. ...If you're interested in making one yourself, feel free to post your design - I'd love to...

(Don't forget to plug in the Micro SD Card adapter and make sure to get the "click") With the SD Adapter in Place, Anycubic will not recognize Insert and Eject of the SD Card because of the missing Card detect Signal. Only way to see new files is to...

A sd card holder for the left side of the Anycubic i3 mega (s).

Sd card extender to mount onto the side of printer. I used double sided tape and it holds well. 3 slots on top for additional SD card storage. Sd card extender from Amazon. Link below. ... ...

The remix will allow the sd card to insert into the Kobra 2 slot and still push and release whereas the original would not. The slot is a tight fit since you can only grab about 2mm of the card and still get it to push in all the way. You can add a...

Optional SD card flipped over to reveal its right side up modification. Dimensions were sourced from the MOSFET add-on by petrzmax, making this project seem entirely feasible. Print at any desired layer height - 0.2mm is more than sufficient. These...

But because I'm always thinking about what may come next - and there's usually something that comes next - this new thingi is perfect in three ways: a) It is fixated with all four screws b) The SD card reader board is also fixed with four screws...

Déplacement du support de SD en face avant

SD card Face Anycubic Mega S. Supports for the board SD about 12 mm. The slot is made with a drill and bored. ...The caps and the board are slightly sharpened at an angle.

Remix from https://www.thingiverse.com/thing:4138044 Thank you for original idea and inspiration! I made it 2mm thicker to allow room for the screw heads inside. I wanted to use 2 screws to hold the board and then attach the whole thing to the...

Compact SD Card Carrier

A simple SD-Card Holder for Anycubic Vyper Material: PLA Support: Yes Printer: Anycubic Vyper

Anycubic i3 MEGA-S SD Card reader Holder

Little SD card holder holder for my anycubic i3 as was always putting them doen and losing them 

This is a custom designed protective cover for the AnyCubic MEGA S 3D printer's SD card slot, crafted to shield your memory cards from dust and accidental damage. Its sleek design allows easy access to the SD card while keeping it safe from harm.

My Anycubic i3 came with a neat USB SD card adapter. ...To keep it close to my printer I created a simple mount for it.

The SD card slot of the Anycubic i3 Mega S is a little difficult to reach. This is a simple holder for a cheap [SD card extension](https://www.aliexpress.com/item/1005003590150308.html) to solve that problem. The cable length of the extension is 10...

I built an external housing for my SD card reader on the Anycubic Mega-S. I routed the ribbon cable down to the bottom of the printer via a convenient slot, which made it simpler to access. ...To secure everything in place, I used double-sided adhesive.

I was having issues with my anycubic mega pro SD card disconnecting midprint, or not showing files. Forums helped me get files to show sometimes once I shortened the file names but still needed to wiggle the card. Electronics contact cleaner and...

Human: 310/5000 Designing a custom enclosure is on my mind, where I plan to house a USB card reader, an extra SD card, and include a hidden slot for inserting the USB connector in case the cover gets lost. I'm open to feedback; if you find this idea...

DescriptionSimple SD Card holder designed to fit the side rails on the Anycubic Vyper 3D printer. You can fit 3 SD Cards, 3 micro SD Cards, and the USB Card Reader supplied with the printer for quick access.Print InstructionsPrint the model with the...

DescriptionSimple SD Card holder designed to fit the side rails on the Anycubic Vyper 3D printer. You can fit 3 SD Cards, 3 micro SD Cards, and the USB Card Reader supplied with the printer for quick access.Print InstructionsPrint the model with the...

Instructions (after opening the bottom plate): - Unscrew the sd card reader and leave it hanging. - Screw the 3D-Freunde V2 mosfet to the mosfet holder. - Push the mosfet holders tubes over the screw sockets of the sd card reader. - Put the sd card...

... SD Card slot covered. ... I exclusively print using OctoPrint, so I needed to conceal the SD Card slot. ... Since Thingiverse no longer clearly labels remixes, here's the original version with a covered SD Slot https://www.thingiverse.com/thing:2920393

This model was built using Tinkercad. ...Modify it instantly at https://www.tinkercad.com/things/zF9S5yQHr7U.

SD Card support for anycubic i3 Mega S. ...I designed this support to put the sd card reader on front of the printer

SD Card Holder for Anycubic Vyper 2.0 (MicroSD, SD, USB Adapter) SD Card Holder from *KlausSalzburg* remixed. I needed to have space also for a micro SD Card and my USB Adapter. Instead of adding another holder, I re-draw the holder in Fusion360. ...

Parts Required: * SD Card Socket * microSD to SD adapter * IDE cable (I opted for the IDE10 cable and removed two wires from it since it only uses eight) * Soldering station along with necessary flux This design is tailored to fit my printer, but...

The Adapter used is the [Cablecc EP-076](https://www.cable.cc/micro-sd-tf-memory-card-kit-male-to-sd-female-extension-soft-flat-fpc-cable-extender-10cm-p-2792.html) The PCB is just glued to the printed part. Make sure that the excess glue isn't...