anycubic vyper change filament during print 3d models

Because I didn't want to print PETG with supprt, I separated the model into to parts, that can be printed separately. ... ipt Files are attached, if you would like to further modify it.

I've printed these in PETG with high infill (70%), but PLA and more shells with less infill probably works as well. The case probably won't get hot enough to make PLA unstable and the profiles stabilize the case anyway once all is connected. You...

Material PLA+ Infill 40%

Did not find that anywhere, maybe someone needs it too. Into the 2 large holes from below M3 sealing nuts, then screw the adapter directly onto the hotend with 4 screws M2.5. The M3 nuts between the screw head and the strain sensor are only in...

<p>Guide made of TPU material for the Z-axis at the top so that it does not wobble.</p>

This is a remix from this thing https://www.thingiverse.com/thing:4942227 I just extended the distance from the screw hole to the actual mount by 20mm, so that I can install the camera as shown in the pictures. I found this to be the best camera...

the original part didn't work for me for long, so i designed a more stable variant are required: 4x threaded insert M3 4x M3x10mm cylinder head screws

<p>My cable chain became a bit loose over time and sagged to the point that sometimes the bed scratched it. ...To prevent this, I designed this simple guide.</p>

Printhead carriage plate Couldn't find the plate anywhere, decided to make it myself. The holes all match and are made a little smaller than they really are. The plate is needed for easy blowing design or to try on a hotend, heating unit. ... upd:...

I couldn’t find anything out there for the beagle camera, so for now all I could think of was with help from another tiktok creator was a triangular base and I used another creators design with approval to make this first prototype. It will remain a...

Another option is to increase the clearance between the printer and the table. It is necessary if you decide to replace the fans with less noisy, but thicker than the original ones. The original shock-absorbing feet must be removed from the...

Customized version of https://www.thingiverse.com/thing:3294615 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3294615

This is my first design. ...I remixed the GoPro attachment from [screw mount camera for Gopro ](https://www.thingiverse.com/thing:53680) For the camera holder in the photos, I used the things from the following designs to mix & match: *...

Customized version of https://www.thingiverse.com/thing:3294615 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3294615

The original designs arm was a bit too short so I wasn't able to properly record. ... I also made the hole a bit bigger so it was a better fit for my webcam screw.

Customized version of https://www.thingiverse.com/thing:3294615 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3294615

https://www.alibaba.com/product-detail/3-in-1-Micro-USB-Hub_60665381993.html This hub is great, functionms properly and adds the required ports to my Octoprint setup. I created this so that the hub does not strain the micro USB port on my RPI...

2 Mal fertigen. Benötigt wird: 4 St. Schrauben M3x12 2 St. Muttern M3 2 St. ...Gewindeeinsatz M3x4x5

Made the stabilizer support opening a bit bigger to fit without having to sand or trim the part. ...The PTFE opening remain the same size.

Another Z-Axis Anti Vibration Ring. ... To be placed under the lid, and on top of the original black plastic ring.

Remixed to fit Raspberry Pi 3B+

Shorter spool to take out some of the slop and extra. Fits up to 1kg spools or up to 2 5/8" wide. ... Tip is 1" Shaft is 7/8" 1/8" lip to keep spool from sliding off

Shoutout to @AndyO7 for the original file. The screw holes have a lot of tolerances, but all screws should still fit just fine. I've also reduced the depth of the extruder mount which allowed me to use the original screws and screw them in properly.

This is a Tray insert, which holds standard size snips as well as the mini ones which came with the printer. Also, a few extra holes to hold spare nozzles....and the usual other tools. The plastic scraper can lie on top. Revisions: -...

This is a spool Holder with integrated bearings (608)

Discontinued!!! New Design https://www.thingiverse.com/thing:4974423 Habe mich mal rangemacht die originalen Lüfter zu ersetzen, da diese unglaublich fiepen wenn sie nicht 100% bekommen. Eins vorweg, es handelt sich noch um Work in...

28-02-2022: Update Platte Mainboard - Kabeldurchlässe vergrößert Ich habe mich durch verschiedene Konstruktionen inspirieren lassen und mir diese Abdeckung für das Mainboard designed. Es ist passend für den Noctua NF-A8 FLX (80x80x25 / 12V)...

X-axes camera holder bed camera holder cover for V-slot Strip led holder Spool holder Z-Axes cover