anycubic vyper change filament during print 3d models

... Mega S was a waste because the filament was making a racket against the spool holder. I made this bracket to hold the fist (print fist at 50 percent size) I mirrored the bracket so i can run the spool off the back or the front and i printed 2 fists.

This is my filament guide design, which combines several ideas - I was inspired by the articulated filament guide concept from Tommytwothousand on Thingiverse: http://www.thingiverse.com/thing:2163508 My model differs significantly if your 3D...

I'm thrilled to show off my brand new filament holder made specifically for the bigger spools - I was so sick of that old metal one! It prints perfectly with just a simple support on the build plate. The best part? ...It clicks right into place without...

A straightforward safeguard that prevents the print head from accidentally snagging onto the filament sensor cable whenever it's returning to its default position. This happens due to a random occurrence, not a deliberate act. ...To resolve this issue,...

... the top plate. Note: my white filament ran out so I finished the print in blue. I also added a trimmed top casing version. I removed some excess material but I have not printed and tried this version yet. ...It should fit the same as the original.

... ... This requires no tools, I printed it out of PLA+ but regular PLA would work, I did 3 walls, 15% infill. Print it with the shaft pointing up, and with support for the two 'nubs' The nubs will go in the holes at the top, they just press in. ...

I was inspired by Tommytwothousand's articulated filament guide on Thingiverse (check it out: http://www.thingiverse.com/thing:2163508). My design takes a different approach. If your printer is well calibrated, the filament guide should have two...

* English * Dual Spool Holder for Anycubic 4Max Required: 10 x 3.16 mm screws, 3 x M4 nuts, 3 x 0.39 inch screws, 2 x 0.79 inch screws, 2 x 0.079 inch T-nuts (2020) Internal spool diameter: 1.77 inches

I designed this filament deflector roll because the filament wasn't running straight through the filament sensor in conjunction with a filament holder mounted to the side of my i3. ...I deliberately chose a larger diameter so that the filament could...

This is for redirecting the filament feed from the front/left corner of the printer. ...This works great with my filament spool holder.

For the DIY version of the AnyCubic Prusa I3, two empty holes are needed on the top side of the main frame. This item is specifically designed to fit those holes perfectly. To assemble the part, you'll need two M3*16 screws and nuts. ...If you'd like to...

Fixing the filament to the top of the device with the original screws. ...

... of the orientation to print it. Note: I painted inside the small hole to stop supports from being put in there as it's not necessary. The hole is a very snug fit for the PTFE tubing so I printed it at a 0.1mm layer height for extra smoothness.

I also redid the filets in the hole for less friction/drag in both directions - extrusion and retraction. Print 100% infill with fins facing up. No supports necessary.Install by unscrewing stock spool holder arm, placing this underneath (with fins...

Attaches securely to the body of a 3D printer, directing the filament straight into the extruder's receiving area.

First submission. ... A simple filament guide, made by using the measurements of the original end-caps of the 2020 aluminum.

Made slightly greater holes for the lens and the ir led's so that it's not requiered to take them off before mounting into the case. ... Replaced the arm mount to fit to the Camera Mount for Anycubic Vyper from TiMo3D. ...

My 3D Printer's filament holder had given out on me, so I opted to utilize the original magnet and design a brand-new holder from scratch.

I started using a usb printer cable to connect my printer to my PC and I noticed the filament reel would rub up against the usb cable. ...This riser is placed on the existing filament reel holder to raise the reel by 20 cm (~.8 inches) which is enough...

You can move the filament holder to the space above the controller to take advantage of the limited space in the enclosure. when it set at an angled, possible to supply filaments for direct extruders. also, possible to attach a commonly used SD...

WORK IN PROGRESS Anycubic Vyper print head replacement. Aim is to fit dual 5105 blower fan instead of the stock 40mm cheap blower fans. Requires: - Two 5105 24v blower fans - some M2 crews to assemble top hood and fan ducts - some larger...

For me the best filament support out there is a remix from https://www.thingiverse.com/thing:2582052, and I also used the big nut of https://www.thingiverse.com/thing:3786473. You'll need 1 8mm threaded rod for the filament support shaft and 2 608zz...

... The intricate details are rendered with stunning clarity thanks to the 0.2mm layer height employed during the printing process. ... Discover more about this captivating creation by visiting the website: https://www.3d-fabric-jean-pierre.com

I need a filament guide for orizzontal top spool holder. I attached the parts with glue. ... Add clamp v2 and guide v2 with m3x5,7 ruthex brass nut hole.

A filament guide to replace the stock spool bracket and smooth the path when using a dryer box. ...Slips on to the same 2 screws the original bracket uses.

Modification of the original filament detection system to integrate seamlessly with the Bondtech extruder is a breeze. ...Simply attach two precision-cut pieces together and you're good to go.

I appreciate the foundation of metraquilate that connects to the filament, however, the base requires refinement. ...I made some adjustments and achieved a satisfying outcome, therefore, I'm sharing this modification with others who may find it...

I didn't like the way the filament came from the top of the printer and had to make a hard angle in through the run out sensor. So, I made this filament guide to eliminate drag and line it up with the sensor. Feel free to improve on this, just...

Cat during scales mini 0.55/1 = 40 x 38 x 1.4 mm - 6min

Created to effortlessly drive the Screw for the Filamentfeeder down without causing finger fatigue when swapping out the filament. Dimensions include a diameter of 1 centimeter and a height of 1 centimeter as well. The inner diameter measures 6.9...