anycubic vyper change filament during print 3d models

Remix mount to center the filament feed to the location on the Anycubic Kossel Series of printers Uses three M3 x 22mm screws to mount the plate and two M3 x 18mm screws and M3 nuts to mount switch. Category: 3D Printer Parts

Just enjoy, redesign if you think. ...The main issue that comes with the Anycubic I3 Mega is a simple tube for filament holder that's not centralized. ...It needs to be rotated 90 degrees so the support lines are at the bottom.

... ... Since I couldn't find a suitable filament sensor holder for the Anycubic i3 Mega-S sensor, I designed this one. The original sensor is positioned directly in the middle under the extruder and assists when the filament is drawn in from below (e.g.

This is a remix of the "Filament Runout Optical Sensor Generic Full Enclosure" by danzca6, which I modified to work with an Anycubic Kossel Linear Plus delta style printer. This mount goes below the stock extruder and can move out or in a few mm to...

Gave me warnings at times and stopped prints at some instances.Did some reading up and realise that sensor is for both 1.75mm and 2.85mm filament, which might become more prone to losing contact if the filament is moving around.I am thinking if i can...

Update 18 Jan 22: I finally got around to changing the filament sensor to another model that is for 1.75mm filament only. Had to change the connector pins from Red middle to the free corner slot. I should not be updating this unless there is still...

(EDIT: The last picture is one I re-printed with a 0.2 nozzle at a .15 layer height if you'd like to see the difference a smaller nozzle makes) * If you like this model and want to contribute (at no cost to you) to a free roll of filament for me, I'm...

I wanted to keep my filament on shelves beside the printer (on a Tush++) not on the top-heavy support holder provided by Anycubic. This guide helps filament across and directs down towards the extruder filament guide. The small guidewheel is...

Держатель датчика филамента для Anycubic Kobra Max Печать PLA

I designed a Simple Filament-Sensor-Holder for my Anycubic i3 Mega printer. The magnet concept didn't appeal to me, so I crafted a holder on my own. It's still rough around the edges but it works just fine right now. In the coming weeks, I plan to...

Upper Filament Reel Platform designed specifically for Anycubic's Kossel plus, adapted to accommodate larger 72.8 mm reels due to the original one being too small for this size. Inside the compressed file, you'll find step-by-step instructions in...

I designed an extension to secure the Anycubic i3 Mega's filament sensor. The sensor is typically held by a small magnet, but it's often not perfectly aligned with the extruder, causing it to come loose frequently. To fix this issue, I created an...

We're here to help you avoid filament sensor issues with your ANYCUBIC I3 MEGA. Our solution makes it simple to install and remove without having to take out the screw or the filament. To get started, follow these steps: 1. Download fss2.stl This...

The print requires approximately 12g (0.42oz) / 3.96m (12.99ft) of filament per brace and takes about 52 minutes according to Cura, but realistically will take around 40 minutes with the specified print settings. For assembly, you'll need: * 2x...

Please note that the support is only designed for spool filament up to one kilogram - I haven't tested it with two kilograms yet! To replace the Spool quickly, no additional bearings are needed - it works very well! I hope you enjoy printing and...

A funnel and tube for guiding the filament into the Anycubic I3 Mega's filament sensor. Assuming you attach the filament sensor directly below the stepping motor, just like I do, without that wobbly magnet. Instructions: - Remove the cover from...

A Simple yet Highly Effective Mod for Printing with the Anycubic i3 Mega TPU. This mod may also be applicable to other printers. An M6 is installed above. The passage hole has a diameter of 2mm. ... I adapted this model solely to meet my needs, as the...

UPDATE: Here is version 2 with changes to the X axis and the roller height https://www.thingiverse.com/thing:5174922 I got worried about the strain the filament was putting on the run out sensor for taller prints, so I made this roller guide that...

Fits the original hole for the filament sensor of the Anycubic i3 Mega S and hooks on the 2 screws above to be securely held in place. Requires an additional M3 screw with at least 12mm length. As I'm using those popular IKEA Lack tables as a...

I've extended the brace for the Anycubic stand, a versatile accessory that allows for the storage and support of two reels of filament. This DIY upgrade replaces the original tube with a 13mm diameter copper pipe, carefully cut to a length of 180cm -...

... They're the last 2 features in the project so if you don't care for fillets just delete them.***  Print recommendations:Make sure to print with the flat bottom side down on the bed100% infill for longevity, less for print speedno supports necessary

They're the last 2 features in the project so if you don't care for fillets just delete them.***  Print recommendations:Make sure to print with the flat bottom side down on the bed100% infill for longevity, less for print speedno supports...

This is a spool holder designed specifically for use with the Anycubic i3 mega 3D printer.

This is a straightforward filament spool holder designed specifically for Anycubic Prusa i3 printers, although it may also work with other models. The spool hangs above the LCD display and is secured via adjustable arms. The arms sit on top of the...

Flexible filament printing can be notoriously challenging with Bowden-style 3D printers, especially when dealing with the critical alignment of the extruder motor and Teflon tubing that guides the filament directly into its path. ...This ingenious part...

The filament spool spins more smoothly when attached directly to the cylinder rather than using the provided holder. ...This results in a straightforward print that doesn't require any special printing settings.

... into the hole of part 2. Secure the fan to the top of both parts, and it should fit perfectly. Print Settings: Printer: Anycubic I3 Rafts: No Supports: No Resolution: 0.2mm Infill: 20-100% Notes: This nozzle cooler may also work on other printers.

I upgraded my i3 Mega to print TPU/TPE, but quickly realized that the extremely soft filament was causing problems as it entered the extruder at a sharp angle. ...To resolve this issue, I designed a custom solution that ensures the filament enters the...

I designed this filament guide to extend the loop of filament away from the printer, and reduce the strain on your Bowden tube. I printed mine in Purple Silk PLA and it worked out quite well. I do recommend PLA I hope you find this design...

Design intended to reduce and/or prevent filament from getting hung up inside the housing of the filament sensor/switch housing. Uses existing mounting bracket and mount in the same two screw locations, but the mounting bracket will now mount...