anycubic vyper filament 3d models

This is a filament guide for the Anycubic Kobra (not Kobra Max).I'm pretty sure this won't help or hurt your prints, its more of an organizational thing. When I started using a bearing aided filament spool holder, the filament would come out in an...

This is a filament guide for the Anycubic Kobra (not Kobra Max). I'm pretty sure this won't help or hurt your prints, its more of an organizational thing. When I started using a bearing aided filament spool holder, the filament would come out in...

This remix its for digispark with micro sd port This is a work in progress Printer: Anycubic Vyper Filament: PLA

Here is the rewritten text: Anycubic Chiron Printer Owner Required Components: 1 x Roller Holder 2 x Pencils 2 x 608 Bearings To install, simply slide the original holder aside and secure in place.

I designed these versatile parts to ensure the spool securely attaches to any support, not just the one that comes with the Anycubic i3 Mega. The conical shape makes them universally compatible. Simply press them into place and they will hold firmly...

Place the item in the 2020 extrusion beneath the extruder, ensuring the filament flows directly into the extruder.

... it was fully loaded. ...To address this concern, I engineered a guide system that expertly positions the filament at the center of the roll. ...With the installation of this guide, the problem of jumping filament has been completely eradicated.

I've been plagued by major issues with filament jumping off the roll when it's full, so I took matters into my own hands and designed a guide that centers the filament perfectly on the roll. With this innovative solution in place, the pesky problem...

I get my best results printing at a fine layer height of .2mm, using a filling percentage of 40-60% with either PETG or PLA filament, along with supports solely on the build plate. ...Afterward, I carefully drill out the filament hole with a precise...

... ... Print with 100% infill for maximum strength but its not necessary. Used zigzag supports for the clip part only. Hole lines up directly over where the filament feeds into the extruder. ... The whole part is out of the way for maximum z travel.

This filament guide shifts the bulk of the tension from the filament switch, allowing it to slide smoothly into place with no rubbing against any components. ...To achieve this, I opted for a high-performance Precision 608 RS ABEC 9 Bearing sourced...

... and make any necessary adjustments before finalizing this step. ----------------- Edit 04/04/2020: I added a "Rollenhalter" feature to ensure smooth unrolling of the filament. ...The print was completed with a layer height of 0.3 millimeters.

Everyone knows it, with leftovers or film end without spindle it can happen that it jumps over the holder. ...This protection prevents this, because it is high enough that the filament does not jump.

Thank you aroerina2 for the awesome design! ...I personally reinforced some areas because the original design was not strong enough to handle 1kg rolls in my opinion. You can find the filament guide here: https://www.thingiverse.com/thing:2700597

This is a filament roller that fits right on top of your i3 Mega to feed direct extruders such as the Titan Aero V6. ...Print it out using PLA plastic at a layer thickness of 0.2 millimeters and use 20 percent infill with supports.

I have not found a straightforward filament guide with no screws or assembly required for a spool located at the rear right of the machine. ...Therefore, I designed this model which installs flawlessly without any need for screws or added complexity!

These holders allow the filament roll to run smoothly on bearings, reducing resistance to a minimum and ensuring a consistent feed. They accommodate bearings with an outer diameter of 12mm and a depth of 3.5-4mm, giving you the flexibility to select...

When paired with the magnet removal mod found on Thingiverse, it skillfully redirects the filament by an impressive 90 degrees. ...After testing, I've found this setup to be effective in limited spaces, providing a neat and efficient solution for my...

This is my remix of a filament guide already out there. My problem with the original design was its lack of support. I added thickness to the walls and made the guide dual sided for added support. All pieces should slide together nicely. Use...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/iHoFqEBDKkT

Remix from https://www.thingiverse.com/thing:4910253

Designed this filament sensor guide after I put the spool holder above the frame for my Anycubic Vyper. The filament began to rub against the top part of the sensor and break the wall. So designed this to help filament to be guided into the filament...

Z screw cover

Hi all, this is my first designed Thingi, based on https://www.thingiverse.com/thing:4942227 You need 5x 5mm cable ties for mounting the cable at the holder. Feel free to use, give me feedback pls. ...Ty.

Un petit support pour metttre un rpi qui heberge octoprint ou astroprint. ... Passe juste sous le plateau, donc ca prends pas de place !

Customized version of https://www.thingiverse.com/thing:2615842 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2615842

Remix of model “V6Adapter-3mmShorter_1.stl” from thing#4976966 which is a remix of thing:4914849 by Glutt0ne The original mount would become loose over time and permit the hot end to turn creating a z-wobble like banding pattern. I added holes for...

UPDATE: I separated the pin and the back part. I also redesigned the back part a bit, so it won't fall off easily. ---- Because I was annoyed with the need to use cable ties each time for holding the printhead-cable in place (and i ran out of...

Remixed arm for 1/4" screw hole for cameras. Check the original thingiverse for the mount and pin. ...Might make a horizonal version later on.

Resized model.