anycubic vyper filament 3d models

This is an improvement version of @taka0909 and already asked him for the credit. There may be some problems in the original designs like the arm is not strong enough and the part is a bit conflict with the lower platform. Also, to make it easier...

modified from the original to have cut sections where the zip ties are placed to be able to cinch down further. ... 0.2mm layer 25% infill 40mm/sec 225oC / 65oC brim 3mm

print it up side to Bed , maybe on an Glass surface. ... Enjoy

Hallo zusammen Ich habe ein Raspberry Pi 4B (8GB) mit OctoPi, Webcam & 2x Temperatur Seonsor für meine Einhausung. Es gibt diverse Halterungen für das Raspberry aber keines hat mir ohne kompromisse gefallen. Beim Drucken ist vielfach die...

Lampholder for dual 5015 Printhead.

Hallo, hier mein Entwurf zum einbau eine Noctua 80x80x25 Lüfter 12 Volt mit Stepp Down Ich habe es noch nicht selber gedruckt aber es sollte passen. Benütigt wird: 1x 80x80x25 Lüfter (Noctua 12 Volt) 1x Stepp Down 24 auf 12 Volt 4x M3x16...

Klammer für das Kabel und den Bowdenzug

I couldn't fine a good mount for my webcam to use with octoprint, so I made my own.

- 10% infill, you may want to increase this for the slider if you want it to block more screen lights.- I used tree support for the case - Recommend to use 0.2mm resolution

Because I was annoyed with the need to use cable ties each time for holding the printhead-cable in place (and i ran out of them), I came up with a permanent solution. So I designed this clip, that fits into the holes in the printhead-backplate and...

Just a stand to hold the hotend for doing any maintenance. So it can be removed from the strain gauge. ... it should have its back on the bed for printing

# If you Made it, # # Put your Photo on "Makes" section. # ## Italiano: ## Coperchio per i v-slot telaio della stamapante. Incastro facile sia dentro che fuori. Puoi utilizzare lo slicer per impostare una lunghezza, per esempio io li ho...

Schutzkappen für die beiden oberen Ecken der Z-Achsen. Schutz vor Staub und Beschädigung. Gedruckt mit TPU, aber andere Materialien sollten auch passen. Der Entwurf ist so gestaltet, dass es locker sitzt. Automatic translation into English ...

Hi this is my first Thing ;-) So have grace with me... ... It is a Camer holder for the Raspberry Pi it can move in all directions Instruction: You need to glue Part 2 and 3 thogeter (may change in future) And for the rest Flathead Screws 4x M4...

Mount for an RaspberryPi Camera

you need 2 x M3 14mm and 2 x M3 6mm and 4 x lock nut have been printing with it for a week now, and it is still working fine

Filamentchange at 0,6mm ruthex M3S Gewindeeinsatz SHORT -... ...https://www.amazon.de/dp/B09MTRHBRL?ref=ppx_pop_mob_ap_share

Helps reduce Vibration on Spool holder

M3 inserts and 4x M3x16 cylinder screws are required.

- 10% infill, you may want to increase this if you'd like the slider cover to block more lights - I used tree support for the case

Remix to fit https://www.thingiverse.com/thing:4977520

<p>The drawing is in mm.&nbsp;</p><p>&nbsp;</p><p>Link to LED lights. ...&nbsp;</p><p>https://www.aliexpress.com/item/1005004068826654.html?spm=a2g0o.order_list.0.0.333d1802cZag1u</p>

Hi this is my first Thing ;-) So have grace with me... ... It is an Camer holder for the Raspberry Pi it can move in all directions Instruction: You need to glue Part 2 and 3 thogeter (may change in future) And for the rest Flathead Screws 4x M4...

Meine Version der X-Achsen Riemenspanner Braucht nicht mehr Platz als das Original. Die beiden Hälften werden mit den Originalschrauben verschraubt. Zusätzlich braucht man noch: 1x M3x20 Sechskantschraube 1x M3 Einschmelzhülse 2x M4x16...

This is a combination/remix of 2 awesome designs made by teenietuss and mightynozzle, but when I search for any Things in the remix section it's blank (or if I search for anything in the remix section for that matter), even if I copy the Thing ID. So...

i don't know much about 3d design but i tried my best to make this because the other ones i found either didn't fit right or the grip was too loose or so tight it squished the tube. ... my sensor still lights up when the printer goes to the far...

Print in PETG or ABS. 100%infill. Layerhöhe geht auch bei 0,2. ... 350ohm DMS vorhandene Kabel vom alten Sensor, oder neue Molex 1,25 mit 4 Pins.

Meine Version der X-Achsen Riemenspanner Braucht nicht mehr Platz als das Original. Die beiden Hälften werden mit den Originalschrauben verschraubt. Zusätzlich braucht man noch: 1x M3x20 Sechskantschraube 1x M3 Einschmelzhülse My...

I couldn't fine a good mount for my webcam to use with octoprint, so I made my own.Print SettingsPrinter Brand:AnycubicPrinter: VyperRafts:NoSupports: NoResolution:0.15mmInfill: 15% GyroidFilament: eSun PLA+ Black   Category: 3D Printer Accessories

Noctua fans used in the original design weren't readily available for me. I went with [be quiet! Pure Wings 2 92mm fans](https://www.bequiet.com/en/casefans/505). Attach the fans with the self-tapping screws which come with the fans. These fans...