anycubic vyper top spool holder 3d models

This new spool holder mount is a basic add-on to let you install the spool holder on the top rail of your Vyper, similar to an Ender 3. Print at any layer height, 75%+ infill, and all other settings based on your filament. I used Overture matte black...

... ...I split the part in two, and extruded the lower part down to make it longer, then rejoined the two parts. I used large cable ties to bind the stock filament spool holder on top of this part, which is sitting on the top rail of the printer. ...

This is my remix of the Anycubic Vyper top spool holder. I noticed that Anycubic seemed to make subtle design tweaks and changes every month with this machine. While the original design worked for many people, my printer (dated Sept 2021) came with...

Thingiverse being weird with linking original: https://www.thingiverse.com/thing:4906483 This is my remix of the Anycubic Vyper top spool holder. I noticed that Anycubic seemed to make subtle design tweaks and changes every month with this machine. ...

Anycubic Vyper / Top, Wall Mount for Spool Holder Use a hammer to deploy :-) No wobble at the mount :-)

This pops in on the top Use your existing spool holder to rest on this. ... You will also need to change the angle of your filament sensor.

The bearing mounts for the top bar on the Vyper were threaded with a 5/16-18 so the bolt can be screwed into the mount and a nut is used to tighten the bolt so it will not loosen. the mount fits the top bar on thee Vyper and it zip tided to hold it...

Ball Baring 608 x3 for Spool Holder Ball Baring 608 x1 for Filament Guide

This is a spool holder that lets you keep the door on your FlashForge Adventurer 3 without making any modifications to the machine for printing external filament. All of the other designs are hours and hours, tons of wasted plastic and you have to...

It is compatible with all kinds of filament spools. Good prints ... *For this apparatus, it is sufficient to print 2 of the files (A1, A2). Print "A1(left).stl" to insert your filament from the back, print A1(right).stl to insert your filament from...

This will allow you to fit a bearing mounted spool holder to your anycubic Vyper original mounting arm.  Hole is for an 8mm bolt and nut. I have included the files for a spoolholder from Tek_3d. ...if you use this you will need a bolt 8mm X 140mm and...

This is a Filament spool holder for the Anycubic Vyper. This Version has got the original locking mechanism. The spool rest is wide enough for the spool to sit with less vibrations. This new, edited Version features a nice japanese Wave-Pattern and...

Spool Holder with Vyper branded text and with fully 3d printed components. ... The 6004 Print in place bearings is a remix with added V-slots for centering the spool.

This is a Filament spool holder for the Anycubic Vyper. This Version has got the original locking mechanism. The spool rest is wide enough for the spool to sit with less vibrations. You will need to print out 2 Parts. Printing: The spool rest can...

Helps reduce Vibration on Spool holder

A simple spool holder adaptater for anycubic vyper to mount the spool on a wall or box. ...

Spool Holder for Anycubic Vyper. 2x 608 ball bearings needed (8x22x7 mm) It's not perfect, but works pretty good. ... Printer: Anycubic Vyper Resolution: 0.2 mm Infill: >=20% Support: Yes Material: PLA+ If you don't have 608 ball bearings, try...

Using 2x 608z bearings this spool holder makes a smaller footprint to your anycubic vyper an an excelent smooth unrolling. ... I made 4 Protoypes and this one went out perfect ;-) Print without support, 50% infill,

The original Anycubic Vyper spool holder takes too much space- so I decided to have the spool holder on the horizontal bridge. The load of the spool is directly on the left pole to avoid to much vibration on the bridge. The filament sensor switch...

The original filament holder used too much space. ...The side spool holder fits into the top rail of the printer and uses the original spool shaft delivered with the Vyper. ...I tried to find the optimum for a minimal footprint of the printer.

Spool Holder for Anycubic Vyper remixed from firebirdrc (thing:5006390), mjoaris (thing:3209211) and Enzi1984 (thing:4971534). Adjusted the Ends to be taller 45.3mm to prevent the spool falling off the holder during a long print. Also included a...

Tired of the filament holder on the Vyper taking up a ton of space? I was too! I couldn't find any designs for a similar part (ones that didn't require metal screws that is) so I decided to make it myself. ...This might not be able to support very heavy...

Original Make: https://www.printables.com/model/126420-anycubic-vyper-filament-spool-holder-with-bearings Original Maker: https://www.printables.com/social/211918-nano3/about The original is a great idea. The bearings work like a charm. I've been...

If you'd like to have 2 spools sit on your spool holder and/or want to support my work with a small amount, you can check out the "nice to have" Version here:...

Spool Holder for Anycubic Vyper remixed from firebirdrc (thing:5006390), mjoaris (thing:3209211) and Enzi1984 (thing:4971534). Adjusted the Ends to be taller 45.3mm to prevent the spool falling off the holder during a long print. Also included a...

Clip-On upgrade for the stock spool holder that comes with the Vyper. Greatly reduces rocking of the spool during printing (especially during retractions)! Easy to clip-on to the stock spool holder. Spools with smaller holes like the TTYT3D one...

Da der originale Anycubic Vyper Spulenhalter sehr schwach ist und mit der zeit ausleiert, habe ich einen zusätzlichen Spulenhalter konstruiert, der einfach in den bestehenden Halter eingeschoben werden kann. ...Der Halter kann somit auf einmal gedruckt...

This is a spool Holder with integrated bearings (608)

Remixed to have the holder rotate with the spool, made the threads longer to accommodate thinner spools. ... hardware: 2 - #608 bearings 1- M8 X 120 bolt 1 - M8 nut Follow print settings from original Note: Print holder and mount with supports as...

... remix of the original to accommodate for the Kobra MAX belt. ...I also lessened the angle slightly, so it isn't quite as steep. This should not interfere with build volume or the upper Belt on the MAX. It also is good for the Vyper and Kobra Plus.