apple tv mount 3d models
382060 3d models found related to apple tv mount.thingiverse
I think there are better versions of Apple TV mounts, but this is good too. You'd print two of these (see pic) - they have screw holes. ... They are almost the same depth as the Apple TV, so it's good to put a piece of foam or somesuch between the...
thingiverse
Updated my original Apple TV mount to the latest dimensions of the 4th generation model. Two versions are available, a small version that saves on material but has adequate support, and a large version which has a taller enclosure. How I Designed...
prusaprinters
This is an alteration of Sinfinity's Apple TV mount (https://www.thingiverse.com/thing:2603682)The main difference is that I added three slots such that a moveable brace can be used to affix the mount to the top of your TV (as the width may vary)...
thingiverse
This is an alteration of Sinfinity's Apple TV mount. The main difference is that I added three slots such that a moveable brace can be used to affix the mount to the top of your TV (as the width may vary) instead. I'd suggest using wood screws here...
thingiverse
A wall mount for the latest Apple TV. ... Since it no longer requires line of sight on the remote, you can use this to mount it behind your TV on the wall and out of sight if you choose.
grabcad
To attach the apple tv to the wall or something (for safety/protection)
thingiverse
Instructions The ATV mount is a simple carriage that holds your Apple TV to the back of a flat-panel television using the VESA screw points. The ATV can operate with either bluetooth or Wi-Fi allowing for rear mounting. The included remote may...
thingiverse
... ...our cat used to always lay in front of it and we were not able to use the remote due to the sensor being blocked by a big black cat......if you have an Apple TV and a big black cat this model was made for you! ...print on its side with no supports
thingiverse
Other designs have it mounted behind the TV but I found the remote would not always work. Distance for TV width is 22mm. I also used the small helper disks as my first printed pulled up. ... ...
thingiverse
This bracket fits the newer, thicker Apple TVs. I have provided two different versions. ...One has rounded corners and slightly different screw holes.
thingiverse
I made this mount to keep an AppleTV on the back of a cheap swivel wall-mount where there was no easy way to mount the AppleTV and still be able to get line of site with the remote. The 3 parts are printed separately, then the Cap is slid up from the...
thingiverse
... This can be printed without support, but some drooping will occur. For best results, print with support. Read more about the design here: http://tech.savvyteachers.com/2012/11/12/stem-in-action-functional-3d-appletv-mount-designed-by-an-8th-grader/
prusaprinters
This Apple TV Mount is using the same mounting design as my other TV Antenna Holder: https://www.thingiverse.com/thing:4706969 https://www.prusaprinters.org/prints/50734-tv-antenna-mount This design is likely another 1-OFF design for my particular...
thingiverse
... No Supports needed. ... Designed for use with the rear VESA mounting screws on a flat panel television. The mount suspends the ATV off the surface of your entertainment center, out of sight and away from reach.
prusaprinters
A remix of https://www.thingiverse.com/thing:244777 No Supports needed. Designed for use with the rear VESA mounting screws on a flat panel television. ...The mount suspends the ATV off the surface of your entertainment center, out of sight and away...
myminifactory
Apple Tv Mount This is my Apple TV mount. ...With this mount you can hang your Apple tv on the back of your monitor or your tv, you can mout in on it with a 7,5 cm bij 7,5 cm vesa mount Material that i used: White PLA 2,85mm Printer: Ultimaker Original
thingiverse
This Apple TV Mount is using the same mounting design as my other TV Antenna Holder: https://www.thingiverse.com/thing:4706969 This design is likely another 1-OFF design for my particular TV, but I'll share all the same. The TV in the Kitchen is an...
thingiverse
Apple TV mount will utilize the vesa tv mount on the back of most modern TVs. No need to use adhesive to attach the mount, just use a screw to attach the mount. I used a M6 x ~15 screw for a Sharp TV. ...
prusaprinters
I needed an easily printable Apple TV mount for my wall in my dorm room. *** It does need supports but just very tiny ones underneath the overhang that actually hold the Apple TV upright, should be an easy print for everyone.
thingiverse
Grandparents wanted an apple TV wall mount, I didn't check Thingiverse until it was almost done printing. This model is far more robust than it needs to be. ...Made for Apple TV HD
thingiverse
This Apple TV wall mount is designed to fit any size Apple TV and an Apple remote. I added the Apple pattern for fun but also for air flow. I recommend printing the version with the Apple logos using support structures to get some nice clean logos. I...
thingiverse
ADDED POSTS to fit IKEA shelf holes and shaved some walls to reduce material and print time.
thingiverse
A variation / extension on user zeq's design. ...The remote was acting a little finicky with the original wall mount so I added an IR reflector. ... Instructions Rhino Beta for Mac OS X
thingiverse
Our Apple TV was just perched on top of the tv in our classroom, so we designed a wall mount so that it can be a little more secure.
thingiverse
Wall mount for Apple TV (98x98x35mm) Print at 100% infill, 0.2 layer height. ... PETG+PLA: Scale to 100% (no scale) ABS+ASA: Scale to 101% to allow for shrinkage 2019/01/18: Added model to support Apple TV model 2 and 3 (98mmx98mmx23mm)
cults3d
Vesa Mount for Apple TV 4K for the rear of the tv. Compatible with: 50x50 75x75 100x100 200x200 Holes are 5mm wide, for M4 screws. Left 1mm extra for heat warp and inaccuracies during printing. ... Back plate itself is 5mm thick Size of the model is...
thingiverse
A very simple Wallmount for the Apple TV 4K Remote. Fix it with double sides tape on the wall. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/iDn2HxQCGoo
pinshape
Designed for Apple tv remote to mount on a vertical surface. Never loss your remote control anymore, now it has its own personal mount! I have a small desk and hate when it gets cluttered. Solution: Mount that remote on the side of my desk. Now I...