aqara motion sensor 3d models

Parts - 1 x Optical Sensor: https://www.amazon.ca/gp/product/B072R4FRDH - 2 x MR115-2RS 5x11x4mm Bearings: https://www.amazon.ca/gp/product/B07CVBW44R - 4 x M2x16mm Screws, Washers and Nuts - 2 x M3x8mm Screws for mounting optical sensor - 2 x...

This is an external WIFI ESP32-Wroom-32U board with a AM312 sensor as the HC sensor had too much false positives. Maybe the AM312 has less or the wifi is seperated enough where I haven't had any to date.. The Board chip is snug on the interior...

This is currently still a work in progress: Enclosure for a WiFi-connected passive infrared (PIR) sensor. This device consists simply of a PIR module and a Wemos D1 mini board. The enclosure allows for the sensor to be pointed. Messages from this...

The sensor detects objects and activates a flashing LED light. In case of an oncoming car, drivers should ideally see this signal. ...If the object draws nearer, an alarm is triggered in case the biker is preoccupied and overlooks the blinking...

Hi, im new to modeling I used another person's project and made it fit with the Arduino UNO using a servo and an ultra sensor it auto-detects and turns on the light :) All Code is here = https://pastebin.com/raw/cJ7z1Mdh

The enclosure allows for the sensor to be pointed. Messages from this device are broadcast via an MQTT host, where they can be picked up by, for instance, a node-red flow or by home automation software. The enclosure is not watertight. ...The one in the...

Corner Holder for IKEA Trådfri Sensor. September 9, 2019: A new 30mm high and 0.7mm wide corner holder was introduced. Its purpose is to provide ample room at the corner to route cables underneath the holder. September 14, 2019: An updated version...

Remix this encoder to meet the parts I had lying around, also made some personal adjustments. Parts 1 x Optical Sensor: https://www.amazon.ca/gp/product/B072R4FRDH 2 x MR115-2RS 5x11x4mm Bearings: https://www.amazon.ca/gp/product/B07CVBW44R 4 x...

I have the first gen IKEA TRÅDFRI motion sensor and turns out if you kick the thing while it's mounted on the wall one or both of the pins that are holding the sensor might brake! If you kick it while it's not mounted on the wall your results may...

This is a 3D printable mounting bracket for a HiLetgo HC-SR501 PIR Infrared Sensor. ...Printed with ABS.

This is a 3D printable mounting bracket for a HiLetgo HC-SR501 PIR Infrared Sensor. ...Printed with ABS.

Support for Xiaomi's wall-mounted motion detector is provided by this corner bracket. I've adjusted the angle to 20 degrees to enhance detection accuracy. No printing supports are required. ...The Rev2 file has a one-millimeter wider base, allowing for...

This is repaired holder model of Stevenson screen for Xiaomi Aqara Temperature, Humidity and Pressure zigbee sensor (https://www.thingiverse.com/thing:4620242).

Holder for outdoor-mounting your Aqara Zigbee tri-sensor. Keeps the sensor away from the mounting surface so as to get a more accurate reading. Slice with an Arachne-enabled slicer! ...No supports required.

I needed a stronger mount for the Outdoor+station+for+Aqara+Temperature+and+Humidity+Sensor\files https://www.thingiverse.com/thing:4223141 wall thickness is 3mm and all the polt and screws holes are 4.5mm Category: Hobby

I needed a stronger mount for the Outdoor+station+for+Aqara+Temperature+and+Humidity+Sensor\files https://www.thingiverse.com/thing:4223141 wall thickness is 3mm and all the polt and screws holes are 4.5mm

Snap the Aqara Temperature and Humidity Sensor into the Frame of the Balance Si Series Wall-Switches from Busch-Jäger with a bit of force - it will click securely into place.

I needed a stronger mount for the Outdoor+station+for+Aqara+Temperature+and+Humidity+Sensor\files https://www.thingiverse.com/thing:4223141 wall thickness is 3mm and all the polt and screws holes are 4.5mm

3D model of IKEA Wireless motion sensor.

Material used: 1x Xiaomi Aqara sensor / 1x Sonoff SNZB-02 sensor 1x top part 3x middle part 1x holder part 2x 5x60 screws TIP: set seam position to be at the back so it wouldn't be visible. ... -- edit -- Just added second version of holder with...

Mounts for Ring motion sensors, designed for installation on dado rails and high ceilings. Two versions, one for mounting on top of dado rails (flat) and one for screwing straight onto the corner directly. ... Spacers for architrave door mounts, I...

Since the adhesive version of the back plates of the Xiaomi Aqara temperature / humidity / pressure or vibration sensors (zigbee models WSDCGQ11LM, DJT11LM) did not seem optimal in many places, I designed a compatible spare part for the back plate...

Since the adhesive back plates of the Xiaomi Aqara temperature / humidity / pressure or vibration sensors (zigbee models WSDCGQ11LM, DJT11LM) did not seem optimal in many places, I designed a compatible spare part for the back plate and based on this...

... work together to hold it securely in place. This custom holder was created specifically to be used outdoors with @Galto2000's Stevenson screen for wireless meteorological sensors, as seen on Thingiverse at https://www.thingiverse.com/thing:83969.

Motion Sensor Light Holder With a Power Bank Holder

Adjustable base for Sonoff motion sensor SNZB-03

Designed for Sonoff Motion Sensor Zigbee device. ... This adapter to holder an Sonoff zigbee motion sensor in the wall.

The sensor is not quite a cube (the top is not as wide as the bottom) and the 4 prongs on this holder have a 6 degree chamfer to hold the sensor in place. ...I made this to use with @Galto2000 Stevenson screen for wireless meteorological sensor, so I...

I Designed my own Active infrared Detector Encasements. This Model is based on a Sparkfun PIR. I Added 12 lights for Impact. I Am currently Working on the Base Panel with Battery Compartment and will Add the Plates Inside for the Terminal Screw...

PLA 0.3 Click firmly into position, ensuring a secure fit. ...A small amount of adhesive may be required to stabilize the piece once it is properly seated.