armattan mongoose 3d models

Armattan Mongoose VTX

Shark fin for enabling anti-turtle mode for Armattan Mongoose frames. ...TPU material is suggested.

My version of a sharkfin for the Armattan Mongoose frame. Holes in top frame is not obstructed so coooling for vtx for example is not affected. ... Feel free to drop a comment.

Antenna mount for the Armattan Mongoose two mounting options 40 degrees or 50 degrees print with supports and brim I have made it to break before the antenna so print a few spares

Antenna mount for the Armattan Mongoose two mounting options 40 degrees or 50 degrees print with supports and brim I have made it to break before the antenna so print a few spares

Here are a number of parts that I've created for my Armattan mongoose. of course you can use a lot of these parts on any quad. Besides the usual Gopro session mount and antenna mounts with my previous build felt very tight inside. I wanted to...

Motor wires protector for Armattan Mongoose!

Armattan Mongoose antenna holder with cap-hole. If your cap doesn`t fit, just wrap some layers electrical tape around it. With an little cutout on the top for the lipo power cable. For foxeer lollipop or similar: Extrude a barrel on top. .ipt file...

... decided to make my own version with normal standoffs and TPU mounts. ... If your more of a freestyle pilot check out my freestyle mods here: https://www.thingiverse.com/thing:4504598 Blog post here: https://tinker.life/2020/10/22/mongoose-parts-part-2/

tutle fin for an Armattan Mongoose FPV Racing Frame

... with insufficient room for a hard mounted gopro mount. ...It was made with the Armattan Mongoose in mind. All credits to Boompy for the original design. Simply place it on the Lipo and strap it down. ...Just beware, battery ejection = GoPro ejection.

Cam mount for mangoose Fit fine with gopro session Need M3x8 and nut like original thing

Not yet tested.

I'm very new to 3D design and this is my first time making an FPV drone canopy and it turned out nice, so I figured I would share it.

Camera holder for using standard size FPV cam (HS1177/Swift/Arrow) on Armattan Mongoose. You need 4pcs 30mm 5.5OD stand off to insert into hole. I print using PLA and need to slowly hammered down the stand off. I think no need if using flex...

Couldn't find one I liked, designed my own. Designed to hold an old style VTx (TS5823L, etc..) the same way as the SCX frames. Includes a small tray on the bottom to hold a Rx like the FrSky XM, XM+, RXSR, or similar in size (12mm or smaller in...

Fin for turtle mode and antenna protection. ... Other modifications (oplional): Reinforced bottom plate: https://armattanproductions.com/pages/product_details/20718 5mm thick arm: https://armattanproductions.com/pages/product_details/22673

Fixed 50° angle Designed for Foxeer Predator Micro 1.8 Lens Suleve M3AS11 standoffs, outer diameter 6mm, length 20mm Other modifications (oplional): Reinforced bottom plate: https://armattanproductions.com/pages/product_details/20718 5mm...

Printed in TPU with 100% infill

I designed a mount specific for my setup, maybe you have the same so here it is :) I have also included the Prusa MK3 settings to print it in sainsmart TPU. ...

This is for Armattan Mongoose with Foxeer Lollipop mmcx or U.fl This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/15MfqHQUtkI

TBS Crossfire Immortal T antenna holder for Armattan Mongoose. It`s working, but not very well. ... Still in progress.

Small piece to fill in the gap at the rear of the Armattan Mongoose to mount a small RX such as the FrSky R-XSR or XFire Nano. the upper half has a mount for an SMA connector, and optionally a way to mount a half board VTX without attaching it to the...

Skin pour Mongoose de chez Armattan en TPU

Skin pour Mongoose de chez Armattan en TPU

Concept by TopotoonPun

View the rendered spaceship showcase at: https://www.deviantart.com/nebulatank/art/Pirate-Mongoose-867524627 View the simulated Novalike spins at: https://www.deviantart.com/nebulatank/art/Pirate-Mongoose-spins-867524643 The original Lightning was...

Low poly 3d model of Mongoose cricket bat: • Number of polygons – 500 • Number of vertices – 502 • Number of tris – 1000 • Unwrapped and textured • Includes .obj & .blend files • Subsurf modifier applied before rendering • Rendered using Blender...

This is a fat Mongoose that I made for my Data Visualization Course. ... I used SculptGL to create a base model, painted and textured it using Microsoft 3d paint, and added a facial sticker for texture.

3d model of Mina Mongoose singing. Character's from the Sonic Archie Comics. Note: arms are rather thin but Mine came out ok thanks to careful removal of supports. just be wary. Also made it free due to unpopularity with this design. ...w/evs