artillery sidewinder x1 firmware 3d models

The Z endstop support for Sidewinder X1 and Genius is designed to be printed in two parts, which are then combined and assembled as shown in the photos. ...To complete this assembly, you'll need a few specific components: a 10 mm M4 Allen screw, a...

Really love the Hemisphere Mounts for the Sidewinder X1, but I had issues with the mounting screws coming loose on the Hemisphere. So, what I did was take the carriage mount and split it into two parts, added two slots for T-Nuts and screw holes.

Small tool to quickly check the correct calibration of the extruder of your sidewinder X1. Put the calibrator on the lever Align the wire in the groove Make marks at the desired levels. ...(10/50/100mm) Make extrusions corresponding to the desired...

Designed for my boxed Sidewinder X1 printer to avoid critical tempratures on the board and swirling in the printing room. Notches in the box for boath parts are required. My box is mounted on the wall, so the notches are both free. it only...

Fast printing low volume spools for Sidewinder X1. Double walled tube printed using vase mode. Inner and outer walls of the tube are close enough together that they fuse together when printed. Use the 6mm version if printing .6mm wide lines. ... ...

This is designed to fit snugly onto the spool holder that comes with the Sidewinder X1. It perfectly accommodates the 14mm (OD) bearings of the spool holder and can handle reels of any width up to 70mm. The Roller tube features ridges at each end to...

Extruderhaube mit Luefter fuer den Sidewinder X1, da der Schrittmotor sehr warm wird, was auf die Dauer nicht gut ist. Die Haube ist unten geschlossen und die Luft wird von vorne angesaugt. Den Fan habe ich parallel zum Hotendluefter angeschlossen....

You can check this with the command M43, but it's disabled by default in the Sidewinder x1 Marlin 1.0.9 FW. To enable it, modify the Configuration_adv.h file using Arduino IDE: search for M43 and remove the "//". Save the file and make a firmware...

STLs A few pre-configured STLs are included that have been rotated for printing (`Rotate_For_Printing` option enabled): `codeandmake.com_Sidewinder_X1_FFC_Riser_v1.0_E3D_Hemera_(parallel).stl` - This is an export of the default settings. This should...

support for fan / BLtouch for the BMG aero from Mellow for the Artillery Sidewinder X1. I use a 40x20 fan for the extruder cooling and a 50x20 blower fan for parts cooling. Also a support for the BLtouch. ... This is the first test version.

Aufsatz für Schublade von Sidewinder X3

Not exactly a remix, but strongly inspired by https://www.thingiverse.com/thing:4001447 by https://www.thingiverse.com/Rics_3D The SideWinder X2 has the same problem with small heatsinks on the stepper drivers just like the X1 with the original...

https://www.thingiverse.com/thing:5200948 Complemento de este otro proyecto, https://www.thingiverse.com/thing:3945539 Sujeción para el cable plano que se mueve en el eje Z de la impresora Artillery X1, creo que valga para la genius, pero esto no lo...

https://www.thingiverse.com/thing:5200948 Complemento de este otro proyecto, https://www.thingiverse.com/thing:3945539 Sujeción para el cable plano que se mueve en el eje Z de la impresora Artillery X1, creo que valga para la genius, pero esto no lo...

 ☕☕☕ PostscriptumApart from the fact that the Super Pinda sensor will bring a better quality of the first layer in your prints, if you don't have an original Prusa like me, then you have the chance to get the first part, which is one of the most...

-------------------------------------------------------- I was unable to find a suitable webcam holder for my Artillery Sidewinder X-1. Most options were either challenging to print or difficult to install. To resolve this issue, I created a simple...

I made this remix for the Artillery Sidewinder Side Chain Cover from the original make from Mauditfou. I couldn't link the remix to him but I am wanting to give him credit for the original creation found here (...

This is a side mounted Raspberry Pi 3b+ and Hyperpixel enclosure for the Artillery Sidewinder 3D printers. Its a remix from the enclosure by ironMANN. It uses his designed top. Follow his instructions for assembling. On the back of my...

when redoing the wiring inside my sidewinder x1 i lost one of the cable routing clips that organizes the wiring. i needed another. i took an old clip, put it on my cheapo printer scanner to get the shape, imported it into GIMP, cleaned the shape...

Der Adapter ist für einen der besten Cam befestigungen die ich für einen Sidewinder X1 hier auf Thingiverse gefunden habe. Keine Schrauberei am Drucker selber notwendig!! V2: -Die Rückseite wurde begradigt, damit sollte für einige Leute das...

Visit my blog: https://3dchanh.com/   The Sidewinder X1 is notorious for how loose the ribbon cables are. The 20-pin connected to the extruder board gets the most abuse so I designed a clamp that will secure it for good. Added an extruder cover that...

The endstops are intended to be mounted at the back of the Sidewinder X1. This design serves as an alternative for those in need of additional mounts for a decoupled Z1 / Z2 axis setup with separate endstops, providing a more precise and reliable...

For those of you who have a duct or something obstructing the front of your extruder, here is a BLtouch mount for the right side on the PCB :) How should I print it? No support needed, just print them as-is and you're good to go For more...

Here is a Z stepper alignment kit I designed for the Sidewinder X1 based on the excellent design of dugacki for the Anet A8 (https://www.thingiverse.com/thing:2684692) Print 2 kits. Slide one ring on each Z screw (just on top of each motor coupler)...

Endstops are meant to be mounted at the back of the Sidewinder X1.  Indended to be a replacement for the stock inductive endstops. Not necessary to improve precision but to provice a good alternative for those in need of additional endswitches for a...

Here is a Z stepper alignment kit I designed for the Sidewinder X1 based on the excellent design of dugacki for the Anet A8 (https://www.thingiverse.com/thing:2684692) Print 2 kits. Slide one ring on each Z screw (just on top of each motor coupler)...

Filament Führung Sidewinder X1 This also fits perfectly with other printers that have a profile frame. To assemble it, you will need: 1. 1 M3 10 mm cylinder head screw 2. ...1 M3 T Slot Nut for attaching to the profile rail There's a new and improved...

Remix of Sidewinder X1 Wyze Cam Mount by baseballjosh: The original printed and fit perfectly, but the camera would noticeably vibrate during smaller sections of solid infills. I reworked the original Base_Mount & Cam_Holder to incorporate two...

... PCB had issues clearing when i installed genuine gates belts. I bent mine a tiny bit with some needle nose vice grips. this is artillery and bondtechs fault lol Simply reset your zero height and run a mesh level and don't forget to save to eprom!

Buy Sidewinder X1 Ultimate Cooler 5015 Radial from me: https://3dchanh.com/my-store/ols/products/sidewinder-x1-ultimate-cooler-5015-radial **Hardware Required:** Version 1: (BLTouch: X 56, Y -34) * Two M4x20 Bolts: Obtain at Amazon.com from DYWISHKEY...