atmel ice 3d models
12714 3d models found related to atmel ice.grabcad
Microchip's Atmel-ICE: basic debugger and programmer for ARM® Cortex®-M, AVR®, and MCU
thingiverse
Simple holder for Atmel ICE programmer/debugger. Holds the device sideways to save space on the base board. Holds the device with a friction fit, with chamfers for easier insertion. Made with countersunk holes for wood screws or CSK machine...
thingiverse
It will accommodate the Atmel ICE PCBA assembly which require only 4 flat head countersunk screws (m2x10) and some adhesive to fully assemble. I have to give credit to "JRodrigo" where much of the inspiration for doing this came from - Be sure and...
thingiverse
A remix of JRodrigo's Atmel-ICE programmer case. Adjusted to make my board fit, not sure if its a newer version or what. ... - Made a recess to fit the through hole connector legs on the bottom of the PCB - Made the opening for the programming...
thingiverse
This is a mod for the middle part of "Enclosure case for ATMEL ICE PCBA programmer/Debugger AVR and SAM" by JRodrigo. You can find it here: https://www.thingiverse.com/thing:2509677 This mod designed to secure the case by four M2 screws and nuts...
prusaprinters
This is a mod for the middle part of "Enclosure case for ATMEL ICE PCBA programmer/Debugger AVR and SAM" by JRodrigo. You can find it here: https://www.thingiverse.com/thing:2509677 This mod designed to secure the case by four M2 screws and nuts with...
thingiverse
This is a protective baseplate for the Atmel ICE Header Adapter PCB from atoomnet.net (https://atoomnet.net/atmel-ice-header-adapter). If you are looking for an Atmel ICE header adapter PCB and the original Atmel stuff for some reason is not for...
thingiverse
This enclosure is designed for a ATMEL ICE PCBA programing tool. You have two options for printing, a three parts or two parts case. #### Three parts case (TOP, MID and BOTTOM) > You can print TOP and MID them separately and glue together. ...
cults3d
Atmel is currently selling its programmer ATMEL ICE programmer as a bare PCB kit http://lt.farnell.com/atmel/atatmel-ice-pcba/debugger-atmel-arm-avr-pcba-kit/dp/2407171?ost=atmel+pcba . This is an enclosure I have designed for this PCB. In few last...
thingiverse
Atmel is currently selling its programmer ATMEL ICE programmer as a bare PCB kit http://lt.farnell.com/atmel/atatmel-ice-pcba/debugger-atmel-arm-avr-pcba-kit/dp/2407171?ost=atmel+pcba . This is an enclosure I have designed for this PCB. In few...
thingiverse
Removed countersink on LED holes and increased diameter to fit 1.75mm transparent filament. ...Fixed missing screw hole.
thingiverse
Small box to hold Atmel Ice and accessories. ...The box accepts 6 mm diameter disk magnets in each corner to securely close the box.
grabcad
... instructions in a single clock cycle, the ATmega48/88/168 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. http://pdf.datasheetcatalog.com/datasheet/atmel/2545S.pdf
thingiverse
Programátor: https://pihrt.com/elektronika/390-programator-atmel-isp-usbasp
grabcad
Microcontrolador ARM Cortex Atmel AT91SAM3X8E -AU 32bit 84Mhz
thingiverse
This box is to organize store and easiest use of 10 routing cards (if you know what it is about). ...For active atmel programmers.
grabcad
a small model of Atmels very popular Atmega 328, 28 pin DIP. ...I was inspired to make this model because i love to use my arduino which is based around the atmega 328.
prusaprinters
Programátor: https://pihrt.com/elektronika/390-programator-atmel-isp-usbasp Post-Printing Category: DIY
thingiverse
... ATmega + ATtiny. You just have to replug the cable, to the right socket. These are the printed parts, which are needed to build the case. You'll find some information and BOM on my private blog:https://flazer.com/blog/14/arduino-atmel-flash-station
thingiverse
You probably have an Atmel/Microchip ATF15XX-DK3 CPLD programmer board at home, but are a bit frustrated that it's basically a bare board that's a little bit untidy (and vulnerable to damage.) Well, fear not, print this base and you'll be good. ... The...
thingiverse
Hallo, die Grundidee des Projektes habe ich auf Youtube gefunden hier die Quelle des Videos: https://www.youtube.com/watch?v=ngKHZZfbhQ0 Für mich war es aber nun nur interessant eine Flash-Station für den Atmel ATmega 328 zu bauen. Ich habe die...
thingiverse
Description from the Atmel website (http://www.atmel.com/tools/AVRDRAGON.aspx): The AVR Dragon sets a new standard for low cost development tools for use with AVR and AVR32 devices with On Chip Debug (OCD) capability. With AVR Dragon you can do...
cgtrader
By executing powerful instructions in a single clock cycle, the ATmega48/88/168 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing...
thingiverse
Arduino uses these microcontrollers)For details of this device see here: http://www.atmel.com/tools/avrdragon.aspx So why is this case special? Wing-Design for easy access I mounted a ZIF-Socket to the AVR Dragon so the case is designed with a...