atomrc f405 3d models
395 3d models found related to atomrc f405.
thingiverse
Caddx Polar mount for AtomRC Dolphin RC plane. ...May fit other 19mm wide cameras as well.
thingiverse
19mm camera mount originally designed for AtomRC Dolphin, with HDZero Micro V2/V3, butprobably fairly generic.
thingiverse
Replacement tail skid for the AtomRC Swordfish.I printed with PETG for durability.Use hot glue or your favorite foam-safe glue to secure it into the slot.
thingiverse
Grid used to release heat and improve front canopy air flow in AtomRC Dolphin, but can be used wherever required. ... This is the one scanned in https://www.thingiverse.com/thing:5905937
thingiverse
Runcam thumb mount (or anything else with that adapter type) for the AtomRC Swordfish. Print settings are whatever you'd like. ...Print with large flat side down, the axis got mixed up during export.
thingiverse
An air inlet for cooling your vtx inside of a depron model. ...I am using this for a AtomRC dolphin. ... I made the duct a bit longer so you can cut it to suit your purpose.
thingiverse
Designed to for use with the AtomRC Dolphin airplane and the GoPro session 4, 5. Uses two 10x2mm circular magnets for connecting to plane. ... Just like the stock noses the magnets are not really sufficient to keep it on during landings so I...
thingiverse
This is an improved mounting motor mounting plate for AtomRC Penguin. Fits 12x12 up to 19x19 motor mounting pattern. ...Print in PETG or ABS with at least 50% infill Note: you will need longer screws to mount the motor on the plate
prusaprinters
Tilt Mount / Nose Cone for the Atomrc Dolphin Only tried with analog so far but would probably fit a digital camera too. Nose cone should provide ample airflow into flight compartmentsRequires 1x 9gram servo and slight modification to fit the...
thingiverse
This is a mount for Caddx Vista DJI VTX for AtomRC dolphin. It goes into the front bay just behind the camera. It can be glued to the base plate or screwed through 4 provided holes (or both) Vista mounts using 20x20mm holes with 4 M2 screws. ... ...
thingiverse
This is an motor guard for the AtomRC Auk quad. You may want to use longer screws to compensate for the added thickness of the guard (I used the original screws and it was fine). ... I didn't have any issues with the motors getting too hot or handling...
thingiverse
Nose for a runcam thumb on the ATOMRC Dolphin. It just snaps right in. I tried to lighten it up a little from the previous design. I printed with the non foaming polylite lw pla, it is lighter than my PLA prototype, which was still light enough,...
thingiverse
My Multi Remix of the AtomRC Dolphin Nose for personal use Supports where needed are included already i use 2x Φ3Φ84mm Bearing i used m3 screws One long m3 goes through the bearing, gear ,Pan plate ,bearing ,and finally screws directly in the Base If...
cults3d
Atomrc Dolphin front cover with different variations. 1) Cover as close to original as i could come 2) Cover sliced for half to print on printers with 180x180x180 dimensions- use super glue! Its easier to print anyway tbh. ...3) Cover sliced with place...
thingiverse
A 3d printed nose replacement for the AtomRC Swordfish, that's specifically designed to house the Walksnail V1 camera, VTX and antennas. The point if this nose/mount is to allow you to fly your Swordfish with a unobstructed view (no nose in view). ...
thingiverse
A hugely improved motor mount for the epic AtomRC Dolphin FPV plane. It fits tight into the motor wire channel, adding much more mechanical stability so it won't just pop off on landing. It also actually has enough space for the screws to not just...
prusaprinters
A hugely improved motor mount for the epic AtomRC Dolphin FPV plane. It fits tight into the motor wire channel, adding much more mechanical stability so it won't just pop off on landing. It also actually has enough space for the screws to not just...
thingiverse
This is a case for a mateksys F405-STD and M8N GPS I pulled from a Radiolink TS100
thingiverse
Glue to the AR Wing Pro with UHU Por. ...Fix the Matek F405-WTE inside using a double sided tape. ...Print in TPU.
thingiverse
Mounting Plate for the Speedy Bee F405 Wing Makes It Easier to remove FC by only gluing down Base Plate to Aircraft
thingiverse
Sonicmodell Binary Matek F405-Wing Board is a revolutionary quadcopter drone that utilizes cutting-edge technology to deliver exceptional performance and stability. Equipped with a robust Matek F405 flight controller, this winged marvel can soar...
thingiverse
It consists of two files: "Tarot680 Matek F405 ninjaflexpartv2" printed first in TPU, and "Tarot680 Matek F405 Non-ninjaflexpartv2" printed afterwards in PLA or PETG without removing the TPU part. Note: -All three versions should be printed upside...
thingiverse
Slide-in mount for Maket F405-WMN flight controller. Friction / interference fit when slid into base, to allow for easy removal for confined builds. No additional hardware required, use original screws with flight controller. Allows for...
thingiverse
I made a custom mount for my betaflight Matek F405 flight controller that attaches it directly to the Tricopter-LR middle plate. ...The mount secures itself to the frame using the tail arm screws, while the flight controller is held in place by 10mm M3...
thingiverse
This is a protection plate for your Mamba F405 Flight controller with USB cutout. But you have to keep in mind, that there's an additional 10mm spacer (standoff) mounted on the stack. So you have to adjust to your demand! ... There's another one...
thingiverse
BB logger case for Mamba F405 mini. Also has a shoe that you can attach to the case.(tho you need screws and nuts) 2021/2/11 updated stl files. Modified the inner bottom of the case so that it holds the nuts secure, also to lower the FC position...