attack on titan 3d animation

Take them off the bed (no raft or brim) and put them on some sticky tape until needed. ..Assembly tips: 1-Take your time gluing the model together and enjoy the process. 2-I used E6000 sticky craft glue to put this model together. The sticky glue...

If you are using a translucent filament like I did, you may want to print the front with 100% infill instead.Print orientations:Front:Back:Mount:Assembly / NotesDon't forget: you have to remove the encoder knob to remove the LCD from the stock case!...

Its storied history is replete with tales of battles won and lost, of heroes and villains, and of the countless lives forever changed by its presence on the battlefield. Throughout time, the Oni Genji Dragonblade has been the subject of much legend...

It also helps me tracking my sport activities or making a call on the way. Advantages:Scalable designEasy printing and assembleConvenient useDifferent ring sizes for different bikesI tested it with a lot of different phones and brands… iPhones...

The AT-AT Walker takes on a new shape, its imposing form now a delicate latticework of patterns. Even the humble AT-ST Scout becomes a work of art, its gentle curves and lines evoking a sense of nostalgia. BB8's endearing appearance is transformed...

3) Next, insert the cable through the top piece and rest it on top of the USB hole. 4) Join the two arm pieces together using an M3x8-M3x12 screw; glue can also be used as a substitute, provided it does not melt inside the car. 5) Insert the screw...

The Switch should NOT open or close when the case is laid face down on a flat surface. The thru hole is meant to be drilled to final size. Refer to project page for electronics assembly instructions. Once you have the electronics assembly wired,...

The wing was built on a single spar which also supported the engine, and a semi-spar/semi-monocoque skin. The armament was concentrated in the nose; a 20 mm Breda cannon with 110 rounds and four 12.7 mm (0.5 in) Breda heavy machine guns with 2,000...

Unfortunately, the conduit manufacturers (Like the DETA brand found here in Australia) simply don't make a viable connector for this purpose, (literally all of mine broke on a gusty day) so I have designed one. So here's my Tee-connector,...

I haven't tried it on a 0.4mm yet, but looking at sliced files it should print fine with a little loss of detail. Post-Printing I had good luck using standard washes when painting this model. With other FDM prints I have had issues with washes...

I printed mine at 75% to save on print space and materials. ...About 6 will fit an Ender 5 at this scale.</p><p>Have a safe Halloween!</p><p>&nbsp;</p><figure class="table"><table><thead><tr><th colspan="3"><strong>Check Out Some of My Other...

There has been some glitches in the rendering with SW's mirror function and it has rendered out colours on parts that weren't assigned to it, whilst other mirrored parts rendered perfectly. Sorry, I have not found a solution yet, as everything...

Two 70x200 TWalls and one Connector take about 12h on my printer. After printing, slide and press the TWall with the top side (slightly rounded) into the Connector, give a final push until you feel a snap and repeat with the other TWall. Pull it...

If your motors are getting hot during flight with the other design, you'll need this component instead.\r\nSkirt: corrected prop clearance; variable camera mount configuration \r\n\r\nSupports are required on V-Tail and A-Tail, use them from the...

... is drilled in part 1 from the desired side and inserted resistor, solder the wire. After that, everything is finally assembled on the necessary coupling. ... The contacts were made from a single-core electric wire of the corresponding section.

To make cutting easier, I recommend printing only one or two layers on the base. The LED holder is also printed in "spiral vase mode," and I created small holes at the top for the wires that connect to the LEDs. At the bottom, I cut out two slots to...

The intricate patterns and shapes that make up our faces, limbs, and torsos are a testament to the incredible diversity and adaptability of life on Earth. Whether we view ourselves as mere machines or complex organisms, it is undeniable that the...

This can be done without any damage to the camera, but requires a bit of finesse.On the bottom of the camera, there is a small gap. Insert a plastic tool and move the tool up and down to separate the back of the camera a...

**Duration** The test session will last approximately 30 minutes, depending on the complexity of the interactions and the human participant's engagement level. **Preparation** Prior to the test session, the human participant should be aware that: ...

Note: I added an additional tab w/ holes on the left side for extra security. You'll just need to drill and tap the holes in the saw. I also add a piece of a silicone mat to this for extra dust collection. • GMC Dust Port - This is an adapter to...

Settings down below.---------------------------------------------------------------------------------------------------------------This print uses Voodoo magic and a 1mm nozzle to enhance print speed while still producing a good quality finish.It...

My design has channels so that the water can rush in during washing and then leave the cavities completely in the typical positions a lid is placed (Handle-UP, for drying or storage) so the handle can dry on the inside quickly. I am aware that FFF...

Get 50% off on all MMF purchases and our latest month release] [PT 1 Contains regular medium-huge models, PT 2 Contains Terrain, Bust and Dragons]   The Liturium War draws to its end. A month of savage battles has seen Coalition forces cut through...

3 https://www.thingiverse.com/thing:4014217 Xmas Star https://www.thingiverse.com/thing:4014412 Other collections… 2018 Holiday Collection https://www.thingiverse.com/timcel/collections/2018-holiday-design-collection Boo!Ville Collection...

It looks a bit like a pineapple but it is supposed to be an explosion :) There are probably some more creative options to fill that corner, so this is on permissive licence to allow you to remix and share. By request I have added a few more...

Pick the hole that's most accessible on your printer. Now loosen the screws holding the end-stop rod in place. Don't remove the rod; just pull it forward a few centimeters so it becomes free at the other end. Now slide over the end-stop mount with...

This version is more sensitive to orientation (it's designed to be installed with the ridge on the bottom), so I made the button-pushing nub smaller, now it won't push the button if installed upside-down. This change is less necessary in the thin...

Like so many others, I found that the friction on that stock tube introduced quite a lot of resistance to the spool's turning until a threshold was reached - then the spool would jump forward a tad. Unacceptable. One of my pix shows the make-shift...

You can also increase the hot end temperature to compensate or run PID tuning with fans on at your desired speed if you really need to run at high speed. Update 5/25/17: A new platform with a little wider clearance is available. Update 3/16/17: A...

The white of the egg is notoriously difficult to disassemble by hand, but spinning the egg on a table makes it come apart with ease. To print this puzzle, you'll need to produce: 3 Shell pieces in light brown 2 White A pieces in white or clear 2...