atx case feet 3d models
231888 3d models found related to atx case feet.thingiverse
The Fractal case feet are a poor design and always break. Here is a simple push fit foot for the bottom of the case. Just push in and it's a tight fit. ...You can always hot glue it in from the inside if you feel like you can't sleep at night.
thingiverse
Instructions for doing your own conversion: http://www.wikihow.com/Convert-a-Computer-ATX-Power-Supply-to-a-Lab-Power-Supply I added 2 amp meters (available from adafruit and other suppliers), each connected to a ground plug, so I can get amp...
thingiverse
This is a ATX PC bench case with 2 fans radiator wather colling support.. ... Print from PLA and mont to 2 aluminium square tubes of 15x15x450mm.
thingiverse
A computer case that can use a Micro ATX motherboard.If your 3D printer can print 330mm*330mm area, you can print it happily!
thingiverse
PiKVM case with ATX control board and OLED screen. Gerber file of ATX board is included. ... OLED screen: https://a.aliexpress.com/_9RsR8z Long screws: M2.5x30 OLED & CSI-bridge screws: 1.7x4 https://easyeda.com/al.pankov/zerow-kvm-v2
thingiverse
final edition of atx board. ... down and top case now with corrected steps just printed at speed 40mm/S (or lest depends on the filament used) layer 0,2mm infill 15/25%
thingiverse
Micro ATX Horizontal Case compatible with Low Profile Graphics cards PC Componentes used: Motherboard Asus P5KPL-VM CPU E8400 3.0Ghz RAM 4G ddr2 800mhz SSD Kingstone 240G Graphics Card GT 710 1G GDDR5 TFX Power Supply Dimentions 360x270x110
thingiverse
Caja de ordenador al aire que encaja perfectamente con placas base ATX, Mini ATX y Micro ATX.
thingiverse
Micro-ATX PC Case Made with Ender 3 v2 All structure 3D printed, with the exception of the side panels Structure made so that the front and side panels, slide on to place with no need for screws. In the Build front panel with vents. ... Side panels...
thingiverse
A simple case for an atx power supply. Hides all the extra wires while still letting it breath and stay cool. ... ** Be sure to flip the back plate over before printing, the underside has a large overhang ** This requires two #4 self tapping screws,...
thingiverse
Replacement basic foot for desktop ATX tower case. ... To get the edges finished smoother so it doesn't snag on flooring or carpet I recommend putting this carefully in an electric drill (small part should fit 1/2" chuck) and file/sand the edges...
thingiverse
I design this ATX Case, because i have a Motherboard Asus P5G41T-M, and i run virtualization servers, and i want a personalized CASE. The size of screw is 100% with the real dimensions of ATX. It´s can be used to motherboards ATX and Mini ATX. My...
prusaprinters
ATX Power Supply Case Print instructionsThis is a simple model to print, but before you do check that back ports of your supply fit into holes and redesign if they dont. On the side there is a port for usb cable. ...I cut one old usb extension cable...
thingiverse
This is a simple case to convert a standard atx power supply to provide 6 outputs. I have used it as 5v, 2x 12v and 3x Ground but any configuration is possible even 3.3v. Knowledge in electrics is required and usually there is no need to open the...
grabcad
This is a full ATX case made to hang on the wall, its made for my own pc specs. I haven't made the fans, motherboard, rams, psu, gpu or the ssd drives, these i've downloaded from this site just to make it look better. If that is not okey with the...
grabcad
Project of designing of Micro ATX computer case was centered around the idea of a removable motherboard which allows for increased accessibility to the computer parts. This project had many changes through the entirety of the project it was very...
thingiverse
This is a full ATX power supply cover, it was designed around a supply I had so you will need to check/edit the back cover to suit your own supply, I built it from scratch in Tinkercad but it's based on a few different designs I've seen on here so if...
thingiverse
This is a simple case for a Duet Wifi powered by an ATX power supply. The power supply gets it's own chamber, with necessary power wires fed up to top chamber. Here there is a 120mm fan placed below the Duet mainboard for cooling. it slots into the...
thingiverse
A power supply cover I designed around a DELL ATX power supply. To eliminate support material, I decided to make the top portion foldable. Holes fit standard Banana plugs. ... The top is attached with aluminum tape, that part could use improvement.
thingiverse
Carrying around my ATX power supply for my heated bead was a real pain so I used http://www.makercase.com/ to make an easier way to carry my printer and power supply at once. Notice that the ATX power supply fan is also cooling my Printrboard. There...
grabcad
My design for a minimalist pc case made from brushed aluminium sheetmetal.
grabcad
Workstation case compatible with Dual-Socket motherboards and up to 12 expansion slots. ...-Up to 6 140mm fans -Up to 420 radiator and 80mm width with 140mm fans.
thingiverse
just a basic mini itx case, needs mesh on the top, front, bottom, and both panels which ever one you pick
thingiverse
Work in progress... ... The Motherboard tray is flipped 180 degrees for some reason. mini itx pc case, for lazer or water jet cuting Made this 5 years ago, and just started to make it better.
thingiverse
Having always been a fan of the design of the Apple G5 case and always having boring generic cases I wanted to make something unique inspired by the G5 case. There are quite some parts to this build, so don't think about printing this overnight. ...
thingiverse
Some basic legs I designed for my 3d Printer. ...They are the same height as an ATX power supply so can be used if you want the ATX supply flush when mounted from above.
grabcad
The rubber part is 1 1/8", if gotten in a rod, you will have to drill a hole unless you use adhesive on top of the foot/feet. ...Hole is 5mm, so should be easily mountable on computer cases or other items that need feet.