audio interface desk mount 3d models

... right next to my headphone holder, so I found this fantastic mount made by Tukanekb8. ...Thanks to his hard work, all I had to do was take off the stand part, drill some screw holes in it, and add dovetail joints for smoother alignment and mounting.

... ...The batteries are positioned at an angle, allowing for easy wall mounting without worrying about them falling out. Four precision-drilled tapered mounting holes enable smooth screw installation and effortless countersinking for a seamless finish.

What is this?This is a boom arm / boom microphone holder for Songmics standing desks.It's designed for el-chapo boom arms that can be found everywhere.It fits pre-cut cable pass-trough hole.What is needed?Parts:6202 ZZ SKF 2Z 15X35X11" bearing.5x...

His file for 1st gen has the incorrect foot-groove size and would not work with 1st gen devices (Serial number's starting with S) If you don't know what generation your device is, see this link:...

Single headphone mount. headphone resting area is lightly curved to evenly dissipate headphones weight to save padding. ... I have one with and one without screws, just use some 3m double sided strong adhesive or a 4mm self threading screw.

The small stops prevent the power supply from sliding out the back, while allowing it to be easily pulled forward without removing the mount. ... ***It should fit most ATX Power Supplies.*** Power Supply Opening Dimensions: approximately 150mm wide and...

Here's a revised version of the text with a rewritten tone and voice: Top Enclosure Bracket Remix: A Custom Fit for Magnum Pulley/Idler Combo Users This clever design seals off the exposed corner where the original idler mount used to be, providing a...

To keep them out of sight and mind, hidden under my desk and other places, I also included mounting tabs in the design. However, this design is not complete, as a cover is yet to be added. As of August 2012, the kit functions and fits as supplied by...

The Audio Amplifier Support used for the InMoov project is held in place by being snapped into its mounting bracket and then secured with either screws or adhesive.

Fairly rough model of a Google Chromecast Audio (model RUX-J42) to allow me to make a 3D-printed mount for it.Created in SOLIDWORKS 2020.

https://community.victronenergy.com/storage/attachments/46216-dl-wnt-v10-datasheet-of-collection-boarddocx.pdf You´ll need some additional asymmetrical screws (2-3mm diameter) for mount the shield in the enclosure. ...If you dont glue the enclosure to...

It is modeled after the mount from Legieps (https://www.thingiverse.com/thing:3801476), but it now is parametric, with only 3 parameters: - The width of the power supply - The heigth of the power supply - The width of the edge that keeps the power...

Assembly Steps: Slide the male end of the extension cable through the bottom part of the mount, which features a small hole. Depending on the print quality, you may need to sand it down for a snug fit. Continue feeding the cable until the female end...

Update: Added holes which should (fingers crossed) work for the Volair Sim Rig that has pre-drilled mounting holes. What you see in the images are holes that I drilled into the model after it was printed. I used M4x20 bolts to mount it on my rig. ...I...

... 2 model into Tinkercad and reshaped it into the Hel. ...Internal dimensions match the dimensions listed on Schiit's website. Haven't tested it out just yet. Print at 0.2 resolution with minimal infill. You will need supports for the mounting holes.

I'm fixing my broken pedestal fan mount/arm using a 3D printer in the spirit of repurposing household items that would otherwise end up in the trash. ... To ensure the new part is sturdy enough to hold the fan head, it needs to be printed with 100%...

A simple holder for the Dell dockingstation to mount it under the table. It is better to add some foam rubber on the inner surfaces, so that the docking station does not wobble back and forth. PS: The Picture show an old version of the right...

Revised Unifi switch under table mount to work with the USW Lite 8 POE switch. I had it printed and it works well for my needs. There is a tiny bit of play in one direction perpendicular to the long direction of the switch (see photos). ...If it bothers...

Crafted in FreeCad for Seamless 3D Printing Created to Print Perfectly Dimensions Must Match at Least 150 x 150 x 150mm Build Platform Extension Limits: Vice Must Not Exceed 70mm Suggested, Up to 85mm Maximum Secure Mounting Allowed Within a Maximum...

Single headphone mount design features a lightly curved resting area to evenly distribute headphones weight and preserve padding. I recommend using either strong adhesive or a self-threading screw for attachment, depending on your preference...

... ... A derivative of my boxes: AAA - https://www.thingiverse.com/thing:3343936 AA - https://www.thingiverse.com/thing:3328879 These organizers have a tilted base and two screw holes. They can be mounted on a wall or placed on a workbench or desktop.

I redesigned the Amazon Echo Dot Mount by Halfway to remove the protruding part that sticks out of the circle, allowing me to place the Echo flat on my monitor shelf for a sleeker look. ...With just a simple snap, the Echo clicks securely into its new...

... holder designed to store up to 23 AA batteries in a secure, angled position. ...This allows for easy wall mounting without worrying about battery ejection. ...Four precision-cut tapered holes enable countersinking of screws for a seamless finish.

The mount I created is straightforward with precise tolerances and should fit easily inside the clamp's port. I'm referring to it as the Theta Mount, and I plan to design more accessories for it in the future. ...I've included a small file containing...

The base of my desk lamp gave way at its weakest point. I had chosen an outlet-style base to start with, but even that proved no match for the weight of the lamp itself. With such a heavy load, there's naturally going to be a lot of pressure on...

... grow. For optimal vice extension, aim for a maximum of 70mm; while 85mm is technically possible, we recommend sticking with the safer option. When it comes to clamping and mounting thickness, you're looking at 40mm with a shim or 45mm without one.

Wall or underdesk mount for USB repeater I designed this for the U305A UNITEK 5M usb c repeater (https://www.ebay.com.au/itm/193804736342) It's possible that it will fit for other repeaters (as i believe its a pretty generic design), but to be sure i...

This is a mounting bracket designed specifically for securing an eight-port Netgear switch, such as those from the GS108 series, underneath a desktop. The bracket features attachment points that align perfectly with the existing screw holes at the...

My PC tower was getting in the way too often, so I decided to mount it under my workbench to solve the problem. I made these for my Dell Optiplex 7010 tower. These could be modified to fit virtually any pc tower, power supply or other electronic...

3D Printed Ring Fit Adventure Ring Con Wall Mount that holds up the Ring-Con and Strap. There are also screw holes at the base of the holder to enable it to be fastened to the edge of a surface. The screw holdes are designed to be compatible with...