audio stand 3d models
159994 3d models found related to audio stand.3docean
Black and wooden audio stand 3d model. ...Compatible with 3ds max 2010 (V-Ray, Mental Ray, Corona) or higher, Cinema 4D R15 (V-Ray, Advanced Renderer), Unreal Engine, FBX and OBJ.
thingiverse
The base is shaped light a Chromecast, and is sturdy enough so the stand doesn't tip over even with a heavy audio or optical cable. Print with the front facing down - no support necessary. Print Settings Printer Brand: ...
thingiverse
First insert the usb cable through the bottom of the stand, then through the front.Plug the cable into the Chromecast audio and the push it into the stand - it's designed to be a snug, friction fit. Once it's in, plug the audio cable into the top. I...
cgtrader
Black and wooden audio stand 3d model. Compatible with 3ds max 2010 (V-Ray, Mental Ray, Corona) or higher, Cinema 4D R15 (V-Ray, Advanced Renderer), Unreal Engine, FBX and OBJ. ...
thingiverse
We couldn't find a stand for our Roland audio recorder, so we made one.
prusaprinters
This is a a stand I built to elevate a small 12 channel audio mixer, Behringer 12 XENYX.If you print this using the stl files, you will need to create two sides with one mirrored. Don't worry about cleanup, the little bit of elephant foot helps to...
thingiverse
I was looking for a headphone stand that I can have near my hand whe I work from home.
thingiverse
A phone holder that allows for optomised audio playback and charging at the same time! ...Took a little while to design and measure.
thingiverse
Use this stand to hold your phone upright while you charge it!
thingiverse
Customized version of http://www.thingiverse.com/thing:258436 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=258436 Instructions Using the following options:...
cults3d
It's been several weeks that my headphones are simply put on the desk, it's not practical because it clutters, it can fall, and it is always where it should not, in short not terrible what!!! So I had to find a solution, I wanted a helmet holder...
thingiverse
My latest project is a headphone holder/stand for my Teufel Aureol headphones. No words to say, just take a look at the pics and enjoy :) I printed the top without any rafts but with support for the connector. The middle/bottom part you need to use...
thingiverse
An audio cassette stand that you can customize! Typically the number of slots is the only thing you'll need to mess with, however you can modify tolerances if you find things too loose or tight. ... This is my first attempt at OpenSCAD, and it was...
thingiverse
My stand broke many years ago. ... Finally got around to designing a new stand. The existing screw won't work so you'll need to go to the hardware store and get a 1/4-20 x .75 bolt and nut. ...
thingiverse
This is a mic stand for a audio control RTA. It fits a 19mm mic. you will need bolts to finish this project. ...The bolt hole opening is 4mm.
thingiverse
Simple stands for audio vacuum tubes. My 10-year-old son designed these based on some wooden ones that were made on a lathe. ...Enjoy!
prusaprinters
Simple stands for audio vacuum tubes. My 10-year-old son designed these based on some wooden ones that were made on a lathe. ...Enjoy!</p> Category: Music
thingiverse
Speaker stands/risers for the Audio Engine A2+ dimensions are 150mmx111mm The images show straight edges, however the stl is 2nd version with beveled edges. ...Which i think gives it a more cleaner look.
thingiverse
Table top stands for the Ruark Audio MR1 speakers. 13 degrees of inclination, no support needed. Add 2-3mm adhesive non slip pads to the feet after printing. ...OpenSCAD source shared in case you want to change / improve something.
thingiverse
This is a stand for the Audio Pro Addon Five -active speakers
thingiverse
the desk stand that came with my M-Audio vocal studio was not stable on my desk and used to tip ove very often. So I designed my own. the stands are a loose fit because I avoided messing with the threads. ...But because of the weight of the microphone,...
thingiverse
Just a simple phone holder, with audio support and (tiny) boost. It support almost all smartphones with cover (12mm). ... Easy and quick to print.
thingiverse
I didn't like the original stand as it takes up too much space so I designed one. You need a 18mm or 20mm M3 screw and a nut to secure the top pieces. I printed it with tree support, 30% infill, 3 wall layers, 0.28mm layer height, 50mm/s. ... I...