auger feeder 3d models
8322 3d models found related to auger feeder.
thingiverse
The original auger is difficult because of the constant overhang and printing with support is a huge PITA. The split model prints each side flat and is glued together afterwards (you'll need to flip the halves down on their long sides before...
thingiverse
I've just increased the size of the hopper by 125mm for my purposes. ...I don't think I did it quite right though.
thingiverse
I obtained the original concept from kitlaan and ultimately settled on using a stepper driven single auger with 2" PVC set up for three independent flow paths. I began with the Noodlepie1002 auger and removed the ends and a 1/2" core from the model....
thingiverse
An auger-based feeder for a Nema 17 stepper motor. Feed your pets on a timer, in certain quantities or remote-controlled by adding a Raspberry Pi or Arduino. Perfect for a pet feeder, aquaponics system or related. I printed all of this in PLA, I...
pinshape
SummaryAn auger-based feeder for a Nema 17 stepper motor. Feed your pets on a timer, in certain quantities or remote-controlled by adding a Raspberry Pi or Arduino. Perfect for a pet feeder, aquaponics system or related. I printed all of this in PLA,...
thingiverse
When driving the servo, you may want to insert reversals at intervals to prevent stressing the servo if kibble gets jammed between the auger and tube. Your servo drive rate(s) may be different; I experimented much. KillAWatt says it's using 2W (0.14A...
thingiverse
Auger . . . Printed vertically, 0.2mm layer height, 0.20 honeycomb infill, 5 outer layers . . . Rev. 1 - hole for motor revised from 5mm to 5.5mm . . . still does not fit motor axle, needs to be increased to maybe 6mm . . ....
thingiverse
The start of an automatic pet feeder project I'm working on.. The motor mount in this design is for a NEMA17 stepper, but that should be easy to change. The exit elbow is not finished, needs a little work. The finished project will be run from a...
myminifactory
The start of an automatic pet feeder project I'm working on.. The motor mount in this design is for a NEMA17 stepper, but that should be easy to change. The exit elbow is not finished, needs a little work. The finished project will be run from a...
thingiverse
... pond feeder. ... Designed this auger to dispense smaller amounts of food. The stock one is for very large ponds. Increased the body diameter and added a extra flight from original factory one. ...this slows down the amount of food being dispensed.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=96462 Instructions Using the following options: Auger_num_flights = 3 Auger_handedness = right Auger_flight_length = 110 Auger_flight_thickness = 1 build_plate_manual_y = 200...
thingiverse
This object is part of the project "Fido Feeder" On Instructables. ...Here is the link http://www.instructables.com/id/Fido-Feeder/
thingiverse
All based around the auger (which I modified), generally copied from : Coberdas If you print all objects you need some additional hardware: PVC drain pipe (40mm). including a 90 degree curve a 45 degree junction and a 45 degree curve And most of...
thingiverse
... has a capacity for about 650 ml. More info about this project here: https://github.com/escaner/catfeeder This is based both on Kitlaan's (remixed from it) and Dodgey99 projects: https://www.instructables.com/Automatic-Arduino-Powered-Pet-Feeder/
thingiverse
small fish feeder with auger system. 12volt 25 RPM gear motor $5.00 3d printed 8mm auger 3D printed hopper and lid. using shelly1 $10.00 from Shelly to control motor. auto power off setting to 3 second in Shelly timer setting. Home Assistant on a...
thingiverse
This is an easy-to print version of the auger for Coberdas' Automatic Fish Feeder project. It's flipped on its edge and split into two parts. Just print both parts and glue them together carefully. ... Advantages: * Easier to print due to no...
thingiverse
https://www.thingiverse.com/thing:1942222 or "Automatic Fish Feeder with micro servo control V2" by pcunha https://www.thingiverse.com/thing:736693 or "Automatic Fish Feeder" by coberdas https://www.thingiverse.com/thing:301532 or "..." Print the 5v...
thingiverse
The original auger looked challenging to mount accurately onto the servo as presented, plus it was non-manifold. It also looks to be quite a workout for an FDM printer, although I didn't try. This model fixes the holes and adds a mount for the...
thingiverse
The JBL Autofood is a nice cost effectiv fish feeder, but the smallest amount of food is still too much for a single fish or several small fish. This auger is designed to reduce the amount of food drastically. ... Designed to work with small...
thingiverse
The auger that comes with the excellently designed original didn't work for me in my small tank with 7 guppies as it was really hard to control the flow of food in such small amounts. I created a new auger with a much lower pitch so it has 11...