automaton cam 3d models

Attached you'll find two pieces that make up the cam cover: Fix Part - This piece will be glued to the screen and should be held in place with instant glue (ethyl-2-cyanacrylate). Be cautious not to apply too much glue, as this could damage your...

... Included some washer thickness in case the alignment to the latching edge is off, mix and match to get desired position or enlarge the direction till desired the height. Affiliate links: Stainless CAM Lock https://s.click.aliexpress.com/e/_AOzffR

Using this clamp you can mount the camera module on a ESP32-Cam board in two orientations. For 90° rotation carefully fold the flex-print cable as shown and put some foam below the camera module, then snap the clamp on. Print Settings Printer Brand:...

 The tailpiece is a tight fit, so a screw is not necessarily needed.The lock fits a standard cam lock opening, and the nut will hold it in place.  Careful not to tighten too much!  The lock cylinder will snap (I discovered the hard...

I found some issues In the camera body, so I fixed them and uploaded the cam only file. I also uploaded the lens as a stand alone file. ... 09/01/2020 - I found some "thin wall" flaws in my test print, so I corrected the model and replaced the old...

My Ring Door View Cam would not fit my door thickness so I quickly printed a spacer to fit between the door and camera to allow correct fitment. Print instructionsPrinter Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: 0.30mm Infill:...

I'm redoing my first car cam project. The original design was too short for the camera and internal components to fit snugly, so I ended up attaching the bottom screws of the camera to the top two holes. Although this worked initially, the PLA...

... shaft, then fasten it to the corner piece with two more M4 screws. Repeat this process for the '12mm cap' and 12mm shaft. Finally, attach the cam to the platform using double-sided tape under its feet or elastic bands for a less permanent solution.

This is a sturdy gimbal mount for an indoor Nest cam. I've printed it out in PLA, but printing in PETG or ABS would probably be a better choice since heat from the camera and sunlight can cause warping issues in the window area. The included bolts...

I've made this box for wallmount for a combined esp32 cam (blank camera is also shown on the picture). Not sure if all of these sold are within the same measurement, so I uploaded the fusion360 file. All parts/bodies are seperated by 0.1mm in this...

Based on the successful high-power rocket flights captured with my 4k action cam, these test flights showcase the mid-power rockets in action. It was a fantastic day spent with SARA, resulting in some thrilling video footage. Big thanks to all...

This innovative cam gear employs an "optimal acceleration sine wave" from Bestehorn, designed for experimental purposes only. ...The creation of the roller and pin bar is largely driven by parameters, but unfortunately, there is no built-in...

The little side clips may not provide a secure hold, but the RunCam2 camera top and action cam mounts underneath effectively keep it in place. Print Settings Printer: Geeetech M201 Rafts: Not necessary for this print. Supports: None required due...

I use Overture PLA filament for its strength properties https://wyze.com/wyze-cam-outdoor.html This allows you to use a bolt (1/4 20 by 3/8 inch with flat washer) or a 25mm by 4mm magnet to attach the camera to the base, or the printed version of a...

After publication, similar models by Nevres (https://grabcad.com/nevres-1) and Ferro (Positive Return Cam) appeared. Created using Solidworks 2015, the model was rendered with Simlab Composer 6 Mechanical Edition and edited for frames in Virtualdub...

This is design to work with a MG90S servo motor and the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes Demo: https://youtu.be/v_A3rCVCbVE Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No...

slides seamlessly into the end of my 20x20 frame and secures my Microsoft Cam a few inches above the plate with a subtle tilt upwards. Functions flawlessly for remote viewing when I'm not near the machine. It's extremely robust and required an...

This is a sleek sleeve/cover for the Wyze Cam v2. Print it upside down, no supports are required. It fits snugly on the camera, giving full access to the back/vents/lens/sensor/IR lights. The fit is perfect - not too tight and not too loose. You can...

This block is designed to fit my complete ecosystem of 3D printed fixtures: 4"x4" Fixture Plate --- https://www.thingiverse.com/thing:3749201 4"x8" Fixture Plate --- https://www.thingiverse.com/thing:3755040 8"x8" Fixture Plate ---...

Wyze Cam Mounting BracketI needed a very simple bracket to mount the Wyze Cam outdoors, on my observatory windowsill. It needed to look sideways at roughly 45 degrees, and the stock mount did not allow for this. The mount is intended to be affixed...

DESCRIPTION The Action CAM Mount is designed for recording Game footage during Nerf Battles. DESIGN NOTES The was a quick project, designed using the mounting parts from the QPS sight (https://www.thingiverse.com/thing:4705126) as the base. The...

This housing is intended for outdoor use of the ESP32-Cam microcontroller. There are fixtures for 5mm LEDs. I use infrared LEDs, so the camera can be used in the dark without visible light. But this requires a small modification of the ESP32 cam...

If your dash cam uses Micro USB or a different size, you can scale down this print for a better fit. These small clips will print quickly, allowing you to experiment with scaling until finding the right size without wasting too much filament. I...

This cable cam mount assembly lets you take your GoPro, Sony, or other action camera for a run along a tensioned line. Two wheels and a body are all part of the design - they're meant to work with regular "608" ball bearings featuring an 8mm core,...

I needed a cam lock device to securely fasten my canoe to the riverbank so that it won't budge when I get in or out. It's versatile, functioning both ways, by simply rotating the thumb wheel in the correct direction. The device is attached to the...

Emoji Cam Cover This isn't a simple print, it's designed to be printed in parts and then assembled as an inlay print. Printed on a Creality with a .35 nozzle and layer height 0.2 using PLA filament from Ctrl Design. Nozzle temperature is set at 210...

If you're a Wyze-Cam-Pan user with a ceiling fan in the same room, you've probably noticed that the camera gets distracted by ceiling fans. In fact, it often ignores its usual task of monitoring areas and tracking motion to focus on the ceiling fan...

For the actual camera housing, you have the option of using the original one from the linked thing above or switching to this one (https://www.thingiverse.com/thing:3407867) that I had to use after upgrading my cam's camera module with an autofocus...

Emoji Cam Cover Not the most straightforward print, but designed to be printed in sections and assembled as an inlay print. This one was printed on a Creality with a 0.35mm nozzle and 0.2 layer height using PLA filament from Ctrl Design off the...

### Adjustable FPV Cam Mount I actually prefer this: https://www.thingiverse.com/thing:2874148 However, it was not a good fit for the giant lens of the Foxeer Cat 3. Four Versions: - 5.0mm standoff diameter for round standoff. - 5.5mm standoff...