axial crawler chassis 3d models
23074 3d models found related to axial crawler chassis.grabcad
Very detailed model of the axles included with the AX10 Chassis from Axial Racing
thingiverse
Chassis Unirversel Court Scale-Crawler.... Pour Skid-Plate central Axial Scx-10.... ...
thingiverse
Chassis stand for the Axial SCX24 micro crawlers This stand was designed fairly generic so it should fit most of the SCX24 crawlers including taller rigs with modifications. ... This fits my deadbolt and Jeep.
thingiverse
Upper deck set up for electronics mounting for crawler chassis. ... I built this to house speed control and receiver for a clod based truck
thingiverse
Chassis Rock Crawler sur Base Scx-10... Liens inférieur et inférieur... Skid-plate central... Transmission... Pont... Amortisseur... ... les supports amortisseurs sont interchangeable(droite/gauche) pour d'autres réglages...
cults3d
Designed to suit the Axial SCX24 chassis and use its full capacity to climp difficult hill. 45° angle here. Either on the torque or with Rpm, choose your best way to cross it. ... https://youtu.be/d9nEt1IRRo8 you need 2 parts for most of the listed...
thingiverse
https://www.thingiverse.com/thing:575054 If you have a box of parts then this makes economical sense, or maybe cheap axles from China but to buy new Axial parts probably not. ... You can see it in action at https://www.youtube.com/watch?v=tnf2rTbt17Y...
thingiverse
This is a simple sandtrack for your Scaler or Crawler. Lenght= 150mm width= 50mm Please hit "like" if you like it. Thanks Instructions Just print the part :-) Maybe you have to scale it x10.
thingiverse
my vehicle is a modified axial scx10 with dual motors. if you have any questions don't hesitate to ask, i have hand made all the pars i can. ... Instructions i have designed it and planed to close it...
thingiverse
I designed this skid plate in an effort to fit trailing arms to my Injora crawler chassis. In the end the chassis just wasn't wide enough to match the trailing arms and the axles (ar60) I wanted to run. I still liked the design, and it's a bit...
thingiverse
I made a new battery tray for my Injora nylon crawler chassis. This is meant to fit the smaller 1500mah battery (~74x37mm). I also built it to mount the battery on the bottom side of the tray as pictured, but it should be able to mount either way.
cults3d
JOKER THEME AXIAL SMT10 CHASSIS PLATES INCLUDES A BLANK PLATE ASWELL FOR STICKERS
thingiverse
Made a chassis for the Wheely/Crawler King from HPI. Designed to use the longer wheelbase links from the Crawler King along with Traxxas Stampede sized bodies. You will need servo on axle steering as this doesn't accommodate the factory style...
cults3d
crawler support for axial scx10 trx4 traxxas and other models very strong support for very heavy load
thingiverse
Made an extended version of he common bomber chassis, hope yall like it
pinshape
le modèle est compatible pour les châssis suivant : -trx4 traxxas -axial scx10 1 -axial scx10 2 -gmade -axial wraith (installer sur les photos) les fichiers sont prés a imprimer. ensemble solide et simple à imprimer. Pour la fixation sur le chassie...
thingiverse
Brought to you by http://RCNewz.com This is a scale winch designed to bolt right onto the front bumper of the Axial SCX10 II Jeep Cherokee RC rock crawler kit. ...It should fit nicely on many other trucks with a bit of drilling to the bumper of your...
thingiverse
Door handle for axial SCX10 Jeep Wrangler
thingiverse
These are bumper brackets for the Axial SCX10. Made these so that I could extend both the front and back to fit a new body. Also added stabilizers to use towards the battery holder as I had to move mine to the front. The battery holders will have to...
thingiverse
It makes the width about the same as other trail crawlers like TRX-4. These also fit over my "TBS" brass portal covers. I ordered them from ebay here - https://www.ebay.com/itm/184060306652 Inside diameter of this wheel is 46mm. There...
prusaprinters
... and the back. The Green are the parts on the crawler. Print instructionsCategory: R/C Vehicles Print Settings Printer: Custom Rafts: No Supports: No Resolution: .1 Infill: 75 Notes: Printed with PLA and PETG, PETG worked very nicely for this part.
cults3d
Stand adapté au Axial scx10 III Galadiator. ...Nécessite 8 vis CHC M3 x 12mm Stand adapted to the Axial scx10 III Galadiator. ...Requires 8 CHC screws M3 x 12mm
thingiverse
These are front fenders for the Axial Deadbolt, some triming of the body is necessary, you need 10 1.4mm bolts to put it in the body.
thingiverse
This is a offroad LED light bar for your scaler/crawler or offroad truck. You just need 150mm of the classic 8mm wide LED stripes. On one side of the housing is a small opening for the cable. The overall length is 154mm with the supports 158mm.
cults3d
Wanted to practice with my crawlers and test their capacity I deisgned this Circular Bump. This is exactly the same shape than the previous bump zone but circular. Then we have a strange form but it it very stable and smooth when the car is going...