axial scx10 winch 3d models
6764 3d models found related to axial scx10 winch.thingiverse
This is a winch mount for the Axial SCX10. It will need to be drilled to your specs. ...Works great on this one!
thingiverse
direct fit to axial scx10.2, replaces servo and battery holder, require tapiing m3 thread since hole is tight fit, around 2.4mm. ...This may not fit all servo hole base in lenght, possible trimming in servo might be required
thingiverse
Brought to you by http://RCNewz.com This is a scale winch designed to bolt right onto the front bumper of the Axial SCX10 II Jeep Cherokee RC rock crawler kit. ...It should fit nicely on many other trucks with a bit of drilling to the bumper of your...
thingiverse
This is not for a front winch, purely designed for rear winching in competition type courses. It requires 4 m3 bolts for the frame rails and 4 M2 bolts for the winch assembly. The fairlead uses the rear mounting bracket already installed on your...
myminifactory
High clearance winch bumper post mount for Axial Scx10-2/3
thingiverse
I tried to get it as close as possible, but added frame mounting and provisions for a Warn-licensed 1:10 scale winch. Uses the RC4WD cable rollers. Tolerances are designed in, so print at 100% scale and make sure your extruder is calibrated. The...
thingiverse
Крепление для рулевой сервы и сервы-лебедки для аксиала второго поколения, совместимо с кузовом чероки.
myminifactory
Monster X winch bumper and grill guard. post mount. ...Grill attaches to bumper with (2) M2x8 countersunk screws
thingiverse
Muffler for the axial scx10-3 Jeep Gladiator. ... Designed to use the original screws.
thingiverse
baca para crawler rc. ...especialmente para el axial scx10 2 k5 blazer pero se puede usar en el que quieras.
thingiverse
Axial SCX10 Dingo parts radiator drivers floor center console Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 10 Post-Printing use double sided tape to affix to body
thingiverse
... nach außen extrudiert damit man diese im nachhinein noch anmalen kann. Und den Verbinder hab ich auch noch neu gemacht Du brauchst: 1x Axial SCX10 III - Links 1x Axial SCX10 III - Rechts 2x Axial SCX10 III - Verbinder 2x drucken 8x M3 6mm Schrauben
thingiverse
This is a bottom plate I created with a cradle for using the twospeed transmission from a Traxxas Summit in an Axial SCX10. This version is for using Axial OEM U-frame. Edit 16-07-08: Holes for links moved down 2mm to clear the frame. Cutout for the...
pinshape
SummaryThis is a bottom plate I created with a cradle for using the twospeed transmission from a Traxxas Summit in an Axial SCX10. This version is for using Axial OEM U-frame. ...The mount for the shiftingservo has to be cut out a little bit to fit the...
thingiverse
Simple exhaust print for axial scx10 (I). One screw (M3) mounts it to the stock frame brace bracket and you can use some zip ties to secure it more. ...Worked with my rc4wd bumper, not sure about the stock one though.
thingiverse
I was playing around and decided to make a drift tire for my axial Scx10. The print time is about 6 1/2 hours on my Monoprice Select Mini V2. ...**note: These tires won't last forever you will eventually will have to reprint them.** Hope you enjoy.
thingiverse
### Axial SCX10 ii Light Bar As it says on the tin, a light bar for the scx10ii. Fits in the roof rack that comes with the Cherokee. I fastened it on by using 3mm nuts and bolts. ... I've included support for both 5mm and 3mm LED's, both take 11...
thingiverse
fits axial scx10 power wagon, possibly other models Instructions when you prepare the file, you will need to select "dont scale" if your software thinks that the thing can't fit. The rotation is off, and it will fit on a print bed at least 8 3/4...
thingiverse
Lift kit for all Axial SCX10 based RC trucks. Adds lift of 14, 20, and 26mm if the lower of the two upper mounts is used, the very top mount adds another 5mm. Pictures show mounting using 3mm hardware into the plastic (could use longer bolts + nut if...
cults3d
Cantilever system for use in crawlers such as Scx10. Adaptable to other car models. ...Needs bearings (8X4x3mm) and separators of 11mm.
thingiverse
A full Axial Deadbolt SCX10II Front Grill that includes a backplate that allows for the use of 5mm leds Print at 100% infill
thingiverse
I recently upgraded to a 5200kv brushless motor with 3s 5500 lipo and beat the snot out of my scx10. i broke the drivers side knuckle on the front axle. i've ordered aluminum replacements but couldn't wait to drive again so i designed and printed a...
thingiverse
Clip is for blocking any cable inside the frame channel rear bumper for adding 4 lights with 8mm buckets front bumper is designed for fitting a winch and need 2 tubes 6mm and I used 8mm diameter tube for fitting the bumper on the chassis. grille...
cults3d
Clip is for blocking any cable inside the frame channel rear bumper for adding 4 lights with 8mm buckets front bumper is designed for fitting a winch and need 2 tubes 6mm and I used 8mm diameter tube for fitting the bumper on the chassis. grille is...
thingiverse
Two mounts and a guide to bolt a standard sized servo converted to a winch in the Axial SCX10 ii frame. The servo goes behind the steering servo and uses all stock mounting holes. For best results use the second half of the clam shell factory cable...
thingiverse
Simple mount to is an Axial transmission as a winch. This is very much a work in progress. You will need to drill out an RC4WD spool to 5mm or make your own. Spot for a bearing on the opposite side of the transmission for the spool to be...
thingiverse
This is a simple fairlead for the Axial Wraith. Mainly applicable if using a servo winch setup. Designed around the stock servo on axle setup, I have not tested with a CMS setup, and I don't have any interest in putting CMS on my Wraith at this time....
cults3d
This is a simple fairlead for the Axial Wraith. Mainly applicable if using a servo winch setup. Designed around the stock servo on axle setup, I have not tested with a CMS setup, and I don't have any interest in putting CMS on my Wraith at this time....